Yamaha YP125R Service Manual Download

Page: 279 / 498

V-BELT AUTOMATIC TRANSMISSION (YP125R)

5-34

EAS37P1027

DISASSEMBLING THE SECONDARY
SHEAVE

1. Remove:

• Clutch carrier nut “1”

TIP

While compressing the compression spring with
the clutch spring holder “2” and clutch spring
holder arm “3”, remove the clutch carrier nut.

EAS37P1028

CHECKING THE CLUTCH HOUSING

1. Check:

• Clutch housing

Damage/wear

→

Replace.

2. Measure:

• Clutch housing inside diameter “a”

Out of specification

→

Replace the clutch

housing.

EAS37P1029

CHECKING THE CLUTCH SHOES

The following procedure applies to all of the
clutch shoes.
1. Check:

• Clutch shoe

Damage/wear

→

Replace the clutch shoes

and springs as a set.
Glazed areas

→

Sand with coarse sandpa-

per.

TIP

After sanding the glazed areas, clean the clutch
with a cloth.

2. Measure:

• Clutch shoe thickness “a”

Out of specification

→

Replace the clutch

shoes and springs as a set.

EAS37P1030

CHECKING THE V-BELT

1. Check:

• V-belt “1”

Cracks/damage/wear

→

Replace.

Grease/oil

→

Clean the primary and second-

ary sheave.

2. Measure:

• V-belt width “2”

Out of specification

→

Replace.

Clutch spring holder

90890-01337

Clutch spring holder arm

90890-01464

Clutch housing inside diameter

135.0 mm (5.31 in)

Limit

135.5 mm (5.33 in)

Clutch shoe thickness

2.0 mm (0.08 in)

Wear limit

1.0 mm (0.04 in)

Summary of Contents for YP125R



















































































































































































































































































































































































































































































































Search results

Summary of Contents for YP125R

Reviews:

Related manuals for YP125R

Brands by name

Popular brands

Yamaha YP125R, Service Manual

Search results

Summary of Contents for YP125R

Reviews:

Related manuals for YP125R

Brands by name

Popular brands