Yamaha YP125R Service Manual Download Page 234

Page: 234 / 498

STEERING HEAD

4-59

EAS23110

REMOVING THE LOWER BRACKET

1. Stand the vehicle on a level surface.

WARNING

EWA13120

Securely support the vehicle so that there is
no danger of it falling over.

2. Remove:

• Upper ring nut “1”
• Lock washer
• Center ring nut
• Rubber washer
• Lower ring nut “2”
• Lower bracket

WARNING

EWA13730

Securely support the lower bracket so that
there is no danger of it falling.

TIP

Remove the upper ring nut and lower ring nut
with the steering nut wrench “3”.

EAS23120

CHECKING THE STEERING HEAD

1. Wash:

• Bearings
• Bearing races

2. Check:

• Bearings
• Bearing races

Damage/pitting

→

Replace.

3. Replace:

• Bearings
• Bearing races

▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼▼▼

a. Remove the bearing races from the steering

head pipe “1” with a long rod “2” and hammer.

b. Remove the bearing race from the lower

bracket “3” with a floor chisel “4” and ham-
mer.

c. Install new bearing races.

NOTICE

ECA14270

If the bearing race is not installed properly,
the steering head pipe could be damaged.

TIP

Always replace the bearings and bearing races
as a set.

▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲▲▲

4. Check:

• Lower handlebar holder
• Lower bracket

(along with the steering stem)
Bends/cracks/damage

→

Replace.

EAS23150

INSTALLING THE STEERING HEAD

1. Lubricate:

• Upper bearing
• Lower bearing
• Bearing races

2. Install:

• Lower ring nut “1”

Steering nut wrench

90890-01403

Exhaust flange nut wrench

YU-A9472

Recommended cleaning solvent

Kerosene

Recommended lubricant

Lithium-soap-based grease

Summary of Contents for YP125R



















































































































































































































































































































































































































































































































Search results

Summary of Contents for YP125R

Reviews:

Related manuals for YP125R

Brands by name

Popular brands

Yamaha YP125R, Service Manual

Search results

Summary of Contents for YP125R

Reviews:

Related manuals for YP125R

Brands by name

Popular brands