background image

IGNITION SYSTEM

8-3

EAS27120

TROUBLESHOOTING

The ignition system fails to operate (no spark or intermittent spark).

TIP

• Before troubleshooting, remove the following part(s):
1. Storage box
2. Front cowling
3. Storage compartment
4. Footrest board

 

 NG

 →

OK

 ↓

 

 NG

 →

OK

 ↓

 

 NG

 →

OK

 ↓

 

 OK

 →

NG

 ↓

 

 NG

 →

OK

 ↓

 

 NG

 →

OK

 ↓

 

 NG

 →

OK

 ↓

1. Check the fuses.

(Main, ECU, and ignition)
Refer to “CHECKING THE FUS-
ES” on page 8-77.

Replace the fuse(s).

2. Check the battery.

Refer to “CHECKING AND 
CHARGING THE BATTERY” on 
page 8-78
.

• Clean the battery terminals.
• Recharge or replace the battery.

3. Check the spark plug.

Refer to “CHECKING THE SPARK 
PLUG” on page 3-24
.

Re-gap or replace the spark plug.

4. Check the ignition spark gap.

Refer to “CHECKING THE IGNI-
TION SPARK GAP” on page 8-83.

Ignition system is OK.

5. Check the spark plug cap.

Refer to “CHECKING THE SPARK 
PLUG CAP” on page 8-82.

Replace the spark plug cap.

6. Check the ignition coil.

Refer to “CHECKING THE IGNI-
TION COIL” on page 8-82.

Replace the ignition coil.

7. Check the crankshaft position sen-

sor.
Refer to “CHECKING THE CRANK-
SHAFT POSITION SENSOR” on 
page 8-83
.

Replace the crankshaft position sen-
sor/stator assembly.

Summary of Contents for YP125R



















































































































































































































































































































































































































































































































Reviews: