manualshive.com logo in svg

Yamaha WR250FM 2021, Owner'S Service Manual


Share
Download
background image

THROTTLE BODY

7-8

b. Remove the fuel tank bolt and lift the fuel

tank.

c. Disconnect the fuel hose from the fuel

pump.
Refer to “REMOVING THE FUEL TANK”
on page 7-2.

WARNING

EWA19380

Cover the fuel hose connection with a cloth

when disconnecting it. This is because re-

sidual pressure in the fuel hose could cause

fuel to spurt out when the hose is removed.

NOTICE

ECA24750

Make sure that the fuel hose is disconnected

by hand. Do not forcibly disconnect the hose

with tools.

d. Connect the pressure gauge “1” and the

fuel pressure adapter “2” to the fuel hose.

e. Start the engine.
f. Measure the fuel line pressure.

Out of specification 

 Replace the fuel

pump.

EAM30273

ADJUSTING THE THROTTLE POSITION 

SENSOR

WARNING

EWA15950

• Handle the throttle position sensor with

special care.

• Never subject the throttle position sensor

to strong shocks. If the throttle position

sensor is dropped, replace it.

1. Check:

•

Throttle position sensor
Refer to “CHECKING THE THROTTLE PO-
SITION SENSOR INPUT VOLTAGE” on
page 8-70.

2. Adjust:

•

Throttle position sensor angle
a. Connect the Yamaha diagnostic tool.

Refer to “YAMAHA DIAGNOSTIC TOOL”
on page 8-31.

b. Temporary tighten the throttle position

sensor.

c. Check that the throttle grip is fully closed.
d. Connect the throttle position sensor to the

wire harness.

e. Set the Yamaha diagnostic tool to “diag-

nostic mode”.

f. Choose the diagnostic code No. “01”.
g. Adjust the throttle position sensor mount-

ed angle until “11”–“14” appears on the
Yamaha diagnostic tool.

h. After adjusting the throttle position sensor

mounted angle, tighten the throttle posi-
tion sensor screw “1”.

Pressure gauge

90890-03153

Pressure gauge

YU-03153

Fuel pressure adapter

90890-03186

Fuel pressure adapter

YM-03186

Fuel line pressure (at idle)

300–390 kPa (3.0–3.9 kgf/cm², 

43.5–56.6 psi)

1

2

1

2

Yamaha diagnostic tool USB (US)

90890-03269

Yamaha diagnostic tool (A/I)

90890-03264

FI diagnostic tool sub–lead

90890-03212

FI diagnostic tool sub–lead

YU-03212

OBD/ GST Leadwire kit

90890-03249

Throttle position sensor screw

3.5 N·m (0.35 kgf·m, 2.6 lb·ft)

T

R

.

.

1

Summary of Contents for WR250FM 2021





















































































































































































































































































































































































































Reviews:

No comments

Related manuals for WR250FM 2021

Ducati 750 Sport Bevel Heaven Workshop Manual preview
750 Sport Bevel Heaven
Brand: Ducati Pages: 235
Wolfman Rocky Mountain-EXP SB-1 Mounting Instructions preview
Rocky Mountain-EXP SB-1
Brand: Wolfman Pages: 7
Baja motorsports Dirt Runner 90cc Owner'S Manual preview
Dirt Runner 90cc
Brand: Baja motorsports Pages: 66
R&G LP0264BK Fitting Instructions Manual preview
LP0264BK
Brand: R&G Pages: 24
kellermann BL 1000 PL Installation Instructions preview
BL 1000 PL
Brand: kellermann Pages: 2
BMW Motorrad HP2 Megamoto Rider'S Manual preview
HP2 Megamoto
Brand: BMW Motorrad Pages: 146
National Cycle N925 Owner'S Manual preview
N925
Brand: National Cycle Pages: 5
kellermann Jetstream Installation Manual preview
Jetstream
Brand: kellermann Pages: 7
SHERCO 2015 450 SEF-R Workshop Manual preview
2015 450 SEF-R
Brand: SHERCO Pages: 76
Abus GameChanger Instruction Manual preview
GameChanger
Brand: Abus Pages: 18
axel joost elektronik Easy RFID Installations Plan preview
Easy RFID
Brand: axel joost elektronik Pages: 2
Serpento COYOTE 250 User Manual/Maintenance preview
COYOTE 250
Brand: Serpento Pages: 66
X-lite X-801 Operating Instructions Manual preview
X-801
Brand: X-lite Pages: 33
DYNATEK D33-1 Installation Instructions preview
D33-1
Brand: DYNATEK Pages: 4
DYNATEK 1003007FONTANASPRINT Installation & User Manual preview
1003007FONTANASPRINT
Brand: DYNATEK Pages: 7
Husqvarna 21012019044 Information preview
21012019044
Brand: Husqvarna Pages: 7
hepco & becker 503998 00 01 Manual preview
503998 00 01
Brand: hepco & becker Pages: 2
Hudora 84201-03 Instructions On Assembly And Use preview
84201-03
Brand: Hudora Pages: 8

Brands by name

Popular brands

Load more brands