manualshive.com logo in svg

Yamaha WR250FM 2021, Owner'S Service Manual


Share
Download
background image

CHASSIS

3-34

EAM30253

CHECKING THE CHASSIS FASTENERS

Make sure that all nuts, bolts, and screws are
properly tightened.
Refer to “CHASSIS TIGHTENING TORQUES”
on page 2-14.

EAM30248

CHECKING AND LUBRICATING THE 

CABLES

The following procedure applies to all of the in-
ner and outer cables.

WARNING

EWA13270

Damaged outer cable may cause the cable to

corrode and interfere with its movement. Re-

place damaged outer cable and inner cables

as soon as possible.

1. Check:

•

Outer cable
Damage 

 Replace.

2. Check:

•

Cable operation
Rough movement 

 Lubricate.

TIP

Hold the cable end upright and pour a few drops
of lubricant into the cable sheath or use a suit-
able lubricating device.

EAM30483

LUBRICATING THE BRAKE LEVER

1. Lubricate the pivoting points and metal-to-

metal moving parts of the following parts.

•

Brake lever

EAM30503

LUBRICATING THE CLUTCH LEVER

1. Lubricate the pivoting points and metal-to-

metal moving parts of the following parts.

•

Clutch lever

EAM30250

LUBRICATING THE PEDAL

1. Lubricate the pivoting point and metal-to-met-

al moving parts of the pedal.

EAM30504

CHECKING THE SIDESTAND

1. Check:

•

Sidestand operation
Check that the sidestand moves smoothly.
Rough movement 

 Repair or replace.

EAM30252

LUBRICATING THE SIDESTAND

Lubricate the pivoting point and metal-to-metal
moving parts of the sidestand.

Recommended lubricant

Engine oil or a suitable cable lu-

bricant

Recommended lubricant

Silicone grease

Recommended lubricant

Lithium-soap-based grease

Recommended lubricant

Lithium-soap-based grease

Recommended lubricant

Lithium-soap-based grease

Summary of Contents for WR250FM 2021





















































































































































































































































































































































































































Reviews:

No comments

Related manuals for WR250FM 2021

X-lite CLEO Installation Instructions preview
CLEO
Brand: X-lite Pages: 5
Abisal Nils Extreme MTW03 User Manual preview
Nils Extreme MTW03
Brand: Abisal Pages: 21
KYMCO X-Town 300 Manual preview
X-Town 300
Brand: KYMCO Pages: 69
NEO TOOLS 97-590 Instruction Manual preview
97-590
Brand: NEO TOOLS Pages: 8
Suzuki 990D0-31J50-CLE Installation Instructions Manual preview
990D0-31J50-CLE
Brand: Suzuki Pages: 12
Yoshimura 070BG125511 Manual preview
070BG125511
Brand: Yoshimura Pages: 4
DYNATEK D3K1-4 Installation Instructions preview
D3K1-4
Brand: DYNATEK Pages: 3
DYNATEK D2K-HD1 User Instructions preview
D2K-HD1
Brand: DYNATEK Pages: 8
Yamaha 2004 Moto Matrix Supplementary Service Manual preview
2004 Moto Matrix
Brand: Yamaha Pages: 41
Yamaha 2004 YZ125F1 Parts Catalog preview
2004 YZ125F1
Brand: Yamaha Pages: 48
Yamaha 2003 TDM900 Supplementary Service Manual preview
2003 TDM900
Brand: Yamaha Pages: 28
Yamaha 2004 FJR1300(S) Supplementary Service Manual preview
2004 FJR1300(S)
Brand: Yamaha Pages: 44
Yamaha 2002 YZF-R6R Service Manual preview
2002 YZF-R6R
Brand: Yamaha Pages: 30
Yamaha 2006 YSF-R1(V) Supplementary Service Manual preview
2006 YSF-R1(V)
Brand: Yamaha Pages: 87
Yamaha 2006 YBR125 Owner'S Manual preview
2006 YBR125
Brand: Yamaha Pages: 84
Yamaha 2006 YZFR6V Owner'S Manual preview
2006 YZFR6V
Brand: Yamaha Pages: 106
Yamaha 2006 YZF-R1V Owner'S Manual preview
2006 YZF-R1V
Brand: Yamaha Pages: 106
Yamaha 2005 V Star XVS1100T Owner'S Manual preview
2005 V Star XVS1100T
Brand: Yamaha Pages: 82

Brands by name

Popular brands

Load more brands