manualshive.com logo in svg

Yamaha WR250FM 2021, Owner'S Service Manual


Share
Download
background image

RADIATOR

6-4

EAM30341

CHECKING THE RADIATOR

WARNING

EWA13030

A hot radiator is under pressure. Therefore,

do not remove the radiator cap when the en-

gine is hot. Scalding hot fluid and steam may

be blown out, which could cause serious in-

jury. When the engine has cooled, open the

radiator cap as follows:

Place a thick rag or a towel over the radiator

cap and slowly turn the radiator cap counter-

clockwise toward the detent to allow any re-

sidual pressure to escape. When the hissing

sound has stopped, press down on the radi-

ator cap and turn it counterclockwise to re-

move.

1. Check:

•

Radiator fin “1”
Obstructions 

 Clean.

Apply compressed air to the rear of the radia-
tor.
Damage 

 Repair or replace.

TIP

Correct any flattened fins with a thin, flat-head
screwdriver.

2. Check:

•

Radiator hose

•

Radiator pipe
Crack/damage 

 Replace.

3. Check:

•

Radiator cap valve opening pressure
a. Install the radiator cap tester adapter “2”

and the radiator cap tester “3” to the radi-
ator cap “1”, and activate the tester to
check whether it can stay for 5 to 10 sec-
onds within standard pressure values.

TIP

Before attaching the cap to the tester, apply wa-
ter to its sealing surface.

No stay 

 Replace.

EAM30506

INSTALLING THE RADIATOR

1. Fill:

•

Cooling system
(with the specified amount of the recom-
mended coolant)
Refer to “CHANGING THE COOLANT” on
page 3-21.

2. Check:

•

Cooling system
Leaks 

 Repair or replace any faulty part.

3. Install:

•

Radiator cap tester “1”

•

Radiator cap tester adapter “2”

Radiator cap valve opening pres-

sure

107.9–137.3 kPa (1.08–1.37 

kgf/cm², 15.6–19.9 psi)

Radiator cap tester

90890-01325

Mityvac cooling system tester kit

YU-24460-A

Radiator cap tester adapter

90890-01352

Pressure tester adapter

YU-33984

Radiator cap tester

90890-01325

Mityvac cooling system tester kit

YU-24460-A

Radiator cap tester adapter

90890-01352

Pressure tester adapter

YU-33984

Summary of Contents for WR250FM 2021





















































































































































































































































































































































































































Reviews:

No comments

Related manuals for WR250FM 2021

Öhlins SD 053 Mounting Instructions preview
SD 053
Brand: Öhlins Pages: 8
BMW Motorrad G 650 GS 2007 Rider'S Manual preview
G 650 GS 2007
Brand: BMW Motorrad Pages: 143
R&G ECC0310R Fitting Instructions Manual preview
ECC0310R
Brand: R&G Pages: 8
R&G FI0056BK Fitting Instructions preview
FI0056BK
Brand: R&G Pages: 4
Yoshimura RACE 13100CP520 Manual preview
RACE 13100CP520
Brand: Yoshimura Pages: 7
Victory Motorcycles Hammer 2005 Owner'S Manual preview
Hammer 2005
Brand: Victory Motorcycles Pages: 332
Honda XL125LK Owner'S Manual preview
XL125LK
Brand: Honda Pages: 243
KTM 60112092010 Information preview
60112092010
Brand: KTM Pages: 7
hepco & becker 6264538 00 01 Mounting Instructions preview
6264538 00 01
Brand: hepco & becker Pages: 3
Fast H-NAPE CHINSTRAP Operator'S Manual preview
H-NAPE CHINSTRAP
Brand: Fast Pages: 24
Yamaha XTZ690 Owner'S Manual preview
XTZ690
Brand: Yamaha Pages: 102
Yamaha XT660R Owner'S Manual preview
XT660R
Brand: Yamaha Pages: 92
Yamaha XT250W Owner'S Manual preview
XT250W
Brand: Yamaha Pages: 86
Yamaha XTZ7N 2021 Owner'S Manual preview
XTZ7N 2021
Brand: Yamaha Pages: 112
Yamaha XTZ7M Owner'S Manual preview
XTZ7M
Brand: Yamaha Pages: 112
Yamaha XT 125R 2005 Service Information preview
XT 125R 2005
Brand: Yamaha Pages: 32
Yamaha XS750-2D Supplemental Service Manual preview
XS750-2D
Brand: Yamaha Pages: 16
Yamaha XT250N 2000 Owner'S Manual preview
XT250N 2000
Brand: Yamaha Pages: 94

Brands by name

Popular brands

Load more brands