manualshive.com logo in svg

Yamaha WR250FM 2021, Owner'S Service Manual


Share
Download
background image

CAMSHAFT

5-17

EAM30081

CHECKING THE CAMSHAFT

1. Check:

•

Camshaft lobe
Blue discoloration/pitting/scratches 

 Re-

place the camshaft.

2. Measure:

•

Camshaft lobe dimensions “A”
Out of specification 

 Replace the camshaft.

3. Measure:

•

Camshaft-journal-to-camshaft-cap clearance
Out of specification 

 Measure the camshaft

journal diameter.

a. Install the camshaft into the cylinder head.
b. Position a strip of Plastigauge® “1” onto

the camshaft journal as shown.

c. Install the dowel pins and the camshaft

caps.

TIP

•

Tighten the camshaft cap bolts in a crisscross
pattern from innermost to outer caps.

•

Do not turn the camshaft when measuring the
camshaft journal-to-camshaft cap clearance.

d. Remove the camshaft caps and then mea-

sure the width of the Plastigauge® “1”.

4. Measure:

•

Camshaft journal diameter “a”
Out of specification 

 Replace the camshaft.

Within specification 

 Replace the cylinder

head and the camshaft caps as a set.

Camshaft lobe dimensions

Lobe height limit (Intake)

32.130 mm (1.2650 in)

Lobe height limit (Exhaust)

33.750 mm (1.3287 in)

Camshaft-journal-to-camshaft-

cap clearance

0.028–0.062 mm (0.0011–0.0024 

in)

2

2

2

1

1

3

3

Camshaft cap bolt

10 N·m (1.0 kgf·m, 7.4 lb·ft)

Camshaft journal diameter

21.959–21.972 mm (0.8645–

0.8650 in)

1

1

1

T

R

.

.

1

1

1

Summary of Contents for WR250FM 2021





















































































































































































































































































































































































































Reviews:

No comments

Related manuals for WR250FM 2021

GBRacing BA12-6-GBR-SET Fitting Instructions preview
BA12-6-GBR-SET
Brand: GBRacing Pages: 2
KTM F3001P2 2016 Setup Instructions preview
F3001P2 2016
Brand: KTM Pages: 29
Ducati MULTISTRADA 1200S Owner'S Manual preview
MULTISTRADA 1200S
Brand: Ducati Pages: 311
Romet CRS 125 User Manual preview
CRS 125
Brand: Romet Pages: 52
rizoma BS232 User Manual preview
BS232
Brand: rizoma Pages: 16
dushi 8712048303945 Assembly Instruction preview
8712048303945
Brand: dushi Pages: 4
hepco & becker 5054558 00 01 Manual preview
5054558 00 01
Brand: hepco & becker Pages: 4
Hudora 84165 Instructions On Assembly And Use preview
84165
Brand: Hudora Pages: 8
Engelbert Strauss 75.76.651 Operating Instructions Manual preview
75.76.651
Brand: Engelbert Strauss Pages: 46
RIEJU TANGO 250 Owner'S Manual preview
TANGO 250
Brand: RIEJU Pages: 152
HYOSUNG ST7 Owner'S Manual preview
ST7
Brand: HYOSUNG Pages: 90
ZONGSHEN ZS250GY-3 Service Manual preview
ZS250GY-3
Brand: ZONGSHEN Pages: 76
Vento Phantom R4i Service Maintenance Manual preview
Phantom R4i
Brand: Vento Pages: 88
X-TREME xm-700 User Manual preview
xm-700
Brand: X-TREME Pages: 6
Beta X-Trainer 300 2T User Manual preview
X-Trainer 300 2T
Brand: Beta Pages: 82
APRILIA PEGASO 650 TRAIL Brochure preview
PEGASO 650 TRAIL
Brand: APRILIA Pages: 12
Royal Enfield Hunter 350 Owner'S Manual preview
Hunter 350
Brand: Royal Enfield Pages: 108
Voloci NiMH User Manual preview
NiMH
Brand: Voloci Pages: 13

Brands by name

Popular brands

Load more brands