manualshive.com logo in svg

Yamaha WR250FM 2021, Owner'S Service Manual


Share
Download
background image

SIGNALING SYSTEM

8-17

EAM30349

TROUBLESHOOTING

•

The speedometer does not operate normally.

•

The fuel level warning light does not come on.

TIP

Before troubleshooting, remove the following part(s):
1. Seat
2. Side cover (left/right)
3. Air scoop (left/right)
4. Fuel tank

Check the signaling system

The speedometer fails to operate.

1. Check the fuse.

Refer to “CHECKING THE FUSES” 

on page 8-59.

NG

Replace the fuse(s).

OK

2. Check the battery.

Refer to “CHECKING AND 

CHARGING THE BATTERY” on 

page 8-60.

NG

•

Clean the battery terminals.

•

Recharge or replace the battery.

OK

3. Check the main relay.

Refer to “CHECKING THE RE-

LAYS” on page 8-62.

NG

Replace the main relay.

OK

4. Check the entire signaling system’s 

wiring.

Refer to “CIRCUIT DIAGRAM” on 

page 8-15.

NG

Properly connect or repair the signaling 

system’s wiring.

OK

This circuit is OK.

1. Check the speed sensor.

Refer to “CHECKING THE SPEED 

SENSOR” on page 8-68.

NG

Replace the speed sensor.

OK

2. Check the entire signaling system’s 

wiring.

Refer to “CIRCUIT DIAGRAM” on 

page 8-15.

NG

Properly connect or repair the signaling 

system’s wiring.

OK

Replace the meter assembly and/or 

ECU.

Summary of Contents for WR250FM 2021





















































































































































































































































































































































































































Reviews:

No comments

Related manuals for WR250FM 2021

Yamaha YZ450F(V) Owner'S Service Manual preview
YZ450F(V)
Brand: Yamaha Pages: 650
ACERBIS STEEL CARBON User Manual preview
STEEL CARBON
Brand: ACERBIS Pages: 72
GLOBBER 505-100 Manual preview
505-100
Brand: GLOBBER Pages: 72
Contracor COMFORT 10130810 Instructions Manual preview
COMFORT 10130810
Brand: Contracor Pages: 36
DYNATEK D3K7-4 Installation Instructions preview
D3K7-4
Brand: DYNATEK Pages: 4
Royal Enfield SCRAM 411 2021 Owner'S Manual preview
SCRAM 411 2021
Brand: Royal Enfield Pages: 110
URAL Motorcycles cT 2022 Owner'S Manual preview
cT 2022
Brand: URAL Motorcycles Pages: 104
Vance and hines Competition Series Quick Start Manual preview
Competition Series
Brand: Vance and hines Pages: 2
Vance and hines 48425 Installation Instructions preview
48425
Brand: Vance and hines Pages: 5
Vance and hines 48241 Installation Instructions preview
48241
Brand: Vance and hines Pages: 4
Peugeot Motorcycles XR6 Workshop Manual preview
XR6
Brand: Peugeot Motorcycles Pages: 50
Denali HMT.04.10200 Instruction Manual preview
HMT.04.10200
Brand: Denali Pages: 2
Healtech QuickShifter easy Supplementary Manual preview
QuickShifter easy
Brand: Healtech Pages: 3
Healtech iLogger easy iLE-1-KIT Supplementary Manual preview
iLogger easy iLE-1-KIT
Brand: Healtech Pages: 4
Yadea M6L Service Menu preview
M6L
Brand: Yadea Pages: 66
APRILIA RS 50 TUONO Use And Maintenance Book preview
RS 50 TUONO
Brand: APRILIA Pages: 88
hepco & becker 701998 00 01 Manual preview
701998 00 01
Brand: hepco & becker Pages: 2
Laverda 500 Workshop Manual preview
500
Brand: Laverda Pages: 151

Brands by name

Popular brands

Load more brands