manualshive.com logo in svg

Yamaha WR250F 2022, Owner'S Service Manual


Share
Download
background image

ENGINE

3-16

NOTICE

ECA25840

If no engine oil seeps out after one minute,

immediately turn the engine off so it will not

seize.

c. If no engine oil seeps out, check the en-

gine oil for leaks, and the engine oil pas-
sage and the oil pump for damage.

d. Check the oil pressure again.
e. Tighten the oil pressure check bolt.

EAM30216

ADJUSTING THE CLUTCH LEVER FREE 

PLAY

1. Check:

•

Clutch lever free play “a”
Out of specification 

 Regulate.

2. Adjust:

•

Clutch lever free play

Handlebar side

a. Turn the adjuster “1” until the specified

clutch lever free play is obtained.

TIP

If the clutch lever free play cannot be obtained
on the handlebar side, use the adjuster on the
clutch cable side.

Clutch cable side

a. Slide the clutch cable cover.
b. Loosen the locknut “1”.
c. Turn the adjuster “2” until the specified

clutch lever free play is obtained.

d. Tighten the locknut “1”.

e. Return the clutch cable cover to its original

position.

EAM30219

CLEANING THE AIR FILTER ELEMENT

1. Remove:

•

Fuel tank cap cover “1”
Refer to “FUEL TANK CAP” on page 1-21.

•

Air filter case cover “2”

TIP

•

Loosen the quick fastener screw “3” and re-
move the air filter case cover.

•

Remove the two ribs “a” located on the left and
right sides of the projections “b” on the air
scoop, and slide the air filter case cover toward
the front of the vehicle to remove it.

2. Turn the plates “1” in direction “a”.

Oil pressure check bolt

10 N·m (1.0 kgf·m, 7.4 lb·ft)

Clutch lever free play

7.0–12.0 mm (0.28–0.47 in)

T

R

.

.

1

Clutch cable locknut

4.3 N·m (0.43 kgf·m, 3.2 lb·ft)

T

R

.

.

1

2

1

2

3

a

b

Summary of Contents for WR250F 2022





















































































































































































































































































































































































































Reviews:

No comments

Related manuals for WR250F 2022

hepco & becker 6616519 01 01 Quick Manual preview
6616519 01 01
Brand: hepco & becker Pages: 4
R&G BRG0004BK Fitting Instructions Manual preview
BRG0004BK
Brand: R&G Pages: 12
Caberg FLIP-UP DUKE X General Instructions Manual preview
FLIP-UP DUKE X
Brand: Caberg Pages: 16
R&G FI0041BK Fitting Instructions preview
FI0041BK
Brand: R&G Pages: 4
Dakota Digital MLX-3000 Manual preview
MLX-3000
Brand: Dakota Digital Pages: 11
Yamaha R3 2021 Owner'S Manual preview
R3 2021
Brand: Yamaha Pages: 108
Yamaha R6 2023 Owner'S Manual preview
R6 2023
Brand: Yamaha Pages: 114
Yamaha PW50W 2007 Service Manual preview
PW50W 2007
Brand: Yamaha Pages: 168
Yamaha R15 2022 Service Manual preview
R15 2022
Brand: Yamaha Pages: 497
Yamaha R1 Series 2015 Service Manual preview
R1 Series 2015
Brand: Yamaha Pages: 704
Yamaha YZF-R15A Owner'S Manual preview
YZF-R15A
Brand: Yamaha Pages: 84
National Cycle ZTechnik Z2386 Quick Start Manual preview
ZTechnik Z2386
Brand: National Cycle Pages: 2
Honda 450X 2005 Owner'S Manual & Competition Handbook preview
450X 2005
Brand: Honda Pages: 180
Malaguti Dune 125 Service Station Manual preview
Dune 125
Brand: Malaguti Pages: 272
bimota DB5 Mille Owner'S Manual preview
DB5 Mille
Brand: bimota Pages: 95
Shad X0SE04P Manual preview
X0SE04P
Brand: Shad Pages: 2
Shad SYM JOYMAX 125 GTS '13 Quick Start Manual preview
SYM JOYMAX 125 GTS '13
Brand: Shad Pages: 2
Shad TOPMASTER Y0RX53ST Quick Start Manual preview
TOPMASTER Y0RX53ST
Brand: Shad Pages: 2

Brands by name

Popular brands

Load more brands