manualshive.com logo in svg

Yamaha WR250F 2022, Owner'S Service Manual


Share
Download
background image

REAR SHOCK ABSORBER ASSEMBLY

4-63

EAM30063

HANDLING THE REAR SHOCK ABSORBER

WARNING

EWA13740

This rear shock absorber contains highly

compressed nitrogen gas. Before handling

the rear shock absorber, read and make sure

you understand the following information.

The manufacturer cannot be held responsi-

ble for property damage or personal injury

that may result from improper handling of

the rear shock absorber.

• Do not tamper or attempt to open the rear

shock absorber.

• Do not subject the rear shock absorber to

an open flame or any other source of high

heat. High heat can cause an explosion due

to excessive gas pressure.

• Do not deform or damage the rear shock

absorber in any way. Rear shock absorber

damage will result in poor damping perfor-

mance.

TIP

A break-in is required up to about 50 km of run-
ning.

EAM30064

DISPOSING OF A REAR SHOCK ABSORBER

Before disposing the rear shock absorber, be
sure to extract the nitrogen gas from valve “1”.

WARNING

EWA19340

• Wear protective glasses to prevent your

eyes from damage due to possible gas or

metal chips scattered.

• To dispose of a damaged or a worn-out rear

shock absorber, take the unit to your

Yamaha dealer for this disposal procedure.

EAM30065

REMOVING THE REAR SHOCK ABSORBER 

ASSEMBLY

1. Use a maintenance stand to raise the rear

wheel off the ground.

WARNING

EWA13120

Securely support the vehicle so that there is

no danger of it falling over.

2. Remove:

•

Rear shock absorber assembly lower bolt “1”

TIP

While removing the rear shock absorber assem-
bly lower bolt, hold the swingarm so that it does
not drop down.

3. Remove:

•

Rear shock absorber assembly upper bolt

•

Rear shock absorber assembly

EAM30067

CHECKING THE REAR SHOCK ABSORBER 

ASSEMBLY

1. Check:

•

Rear shock absorber rod
Bends/damage 

 Replace the rear shock

absorber assembly.

•

Rear shock absorber
Gas leaks/oil leaks 

 Replace the rear shock

absorber assembly.

•

Spring
Damage/wear 

 Replace.

•

Spring guide
Damage/wear 

 Replace.

•

Bearing
Damage/wear 

 Replace.

•

Bolt
Bends/damage/wear 

 Replace.

1

1

Summary of Contents for WR250F 2022





















































































































































































































































































































































































































Reviews:

No comments

Related manuals for WR250F 2022

Suzuki RM250 Owner'S Service Manual preview
RM250
Brand: Suzuki Pages: 151
VIKING BAGS MINI TANK BAG Installation Instructions preview
MINI TANK BAG
Brand: VIKING BAGS Pages: 2
DMC 25470-00 Installation Instructions preview
25470-00
Brand: DMC Pages: 2
zeeltronic PDCI-30 User Manual preview
PDCI-30
Brand: zeeltronic Pages: 10
hepco & becker LOCK-IT 506007-7 Manual preview
LOCK-IT 506007-7
Brand: hepco & becker Pages: 2
Yamaha XV17ATMV(C) Road Star Owner'S Manual preview
XV17ATMV(C) Road Star
Brand: Yamaha Pages: 108
Yamaha XT250P Owner'S Manual preview
XT250P
Brand: Yamaha Pages: 100
Yamaha XTZ12D(C) Owner'S Manual preview
XTZ12D(C)
Brand: Yamaha Pages: 118
Yamaha Super Tenere ES 2022 Owner'S Manual preview
Super Tenere ES 2022
Brand: Yamaha Pages: 132
Yamaha XT250X 2008 Service Manual preview
XT250X 2008
Brand: Yamaha Pages: 282
Yamaha Super Tenere ES 2020 Owner'S Manual preview
Super Tenere ES 2020
Brand: Yamaha Pages: 130
Yamaha TDM850 User Manual preview
TDM850
Brand: Yamaha Pages: 211
Shark Heritage Manual preview
Heritage
Brand: Shark Pages: 80
hepco & becker 630209 Assembling Instructions preview
630209
Brand: hepco & becker Pages: 6
Burro Max Burromini-Gas TT40 Owner'S Manual preview
Burromini-Gas TT40
Brand: Burro Max Pages: 34
R&G FI0112BK Fitting Instructions preview
FI0112BK
Brand: R&G Pages: 4
Chicago Electric 47996 Assembly And Operating Instructions Manual preview
47996
Brand: Chicago Electric Pages: 7
Chicago Electric 91212 Set Up And Operating Instructions Manual preview
91212
Brand: Chicago Electric Pages: 10

Brands by name

Popular brands

Load more brands