manualshive.com logo in svg

Yamaha WR250F 2022, Owner'S Service Manual


Share
Download
background image

STARTING AND BREAK-IN

1-34

NOTICE

ECA10262

• When shifting, press the shift pedal firmly

until you feel the gear shift is complete.

• Even with the transmission in the neutral

position, do not coast for long periods of

time with the engine off, nor tow the motor-

cycle for long distances. The transmission

is properly lubricated only when the engine

is running. Inadequate lubrication may

damage the transmission.

• Always use the clutch while changing

gears to avoid damaging the engine, trans-

mission, and drive train, which are not de-

signed to withstand the shock of forced

shifting.

To start out and accelerate

1. Pull the clutch lever to disengage the clutch.
2. Shift the transmission into first gear.
3. Open the throttle gradually, and at the same

time, release the clutch lever slowly.

4. At the recommended shift points shown in the

following table, close the throttle, and at the
same time, quickly pull the clutch lever in.

5. Shift the transmission into second gear.

(Make sure not to shift the transmission into
the neutral position.)

6. Open the throttle part way and gradually re-

lease the clutch lever.

7. Follow the same procedure when shifting to

the next higher gear.

TIP

When shifting gears in normal operating condi-
tions, use the recommended shift points.

To decelerate

1. Apply both the front and the rear brakes to

slow the motorcycle.

2. Shift the transmission into first gear when the

motorcycle reaches 20 km/h (12 mph). If the
engine is about to stall or runs very roughly,
pull the clutch lever in and use the brakes to
stop the motorcycle.

3. Shift the transmission into the neutral position

when the motorcycle is almost completely
stopped.

Recommended shift points

The recommended shift points during accelera-
tion and deceleration are shown in the table be-
low.

1

1

1

1

2

3

4

5

6

N

1

2

3

4

5

6

N

Shift up points

1st 

 2nd

20 km/h (12 mph)

2nd 

 3rd

30 km/h (19 mph)

3rd 

 4th

40 km/h (25 mph)

4th 

 5th

50 km/h (31 mph)

5th 

 6th

60 km/h (37 mph)

Shift down points

6th 

 5th

45 km/h (28 mph)

5th 

 4th

35 km/h (22 mph)

4th 

 3rd

25 km/h (16 mph)

3rd 

 2nd

25 km/h (16 mph)

2nd 

 1st

25 km/h (16 mph)

Summary of Contents for WR250F 2022





















































































































































































































































































































































































































Reviews:

No comments

Related manuals for WR250F 2022

Idaho Star Operator'S Manual preview
Star
Brand: Idaho Pages: 72
GAS GAS TXT PRO - PART LIST CHASSIS 2003 Parts List preview
TXT PRO - PART LIST CHASSIS 2003
Brand: GAS GAS Pages: 36
MOTO GUZZI V 35 Owner'S Manual preview
V 35
Brand: MOTO GUZZI Pages: 61
Memphis Shades MEM5806 Quick Start Manual preview
MEM5806
Brand: Memphis Shades Pages: 2
R&G CP0482 Fitting Instructions Manual preview
CP0482
Brand: R&G Pages: 18
X-lite X-902 Directions For Use Manual preview
X-902
Brand: X-lite Pages: 84
R&G AB0036 Fitting Instructions Manual preview
AB0036
Brand: R&G Pages: 27
hepco & becker 630727 00 01 Manual preview
630727 00 01
Brand: hepco & becker Pages: 3
Yamaha WR450FX Owner'S Service Manual preview
WR450FX
Brand: Yamaha Pages: 220
Yamaha WR450FN 2022 Owner'S Service Manual preview
WR450FN 2022
Brand: Yamaha Pages: 402
Yamaha WR450F 2021 Owner'S Service Manual preview
WR450F 2021
Brand: Yamaha Pages: 402
Yamaha WR450F 2022 Owner'S Manual preview
WR450F 2022
Brand: Yamaha Pages: 176
Yamaha TT-R90(V) Owner'S Service Manual preview
TT-R90(V)
Brand: Yamaha Pages: 390
Yamaha TTR125LM Owner'S Service Manual preview
TTR125LM
Brand: Yamaha Pages: 468
Yamaha TT-R90(T) Owner'S Service Manual preview
TT-R90(T)
Brand: Yamaha Pages: 364
MOTO GUZZI V7 CLASSIC Service Manual preview
V7 CLASSIC
Brand: MOTO GUZZI Pages: 134
SUOMY MX SPEED Manual preview
MX SPEED
Brand: SUOMY Pages: 26
DYNATEK D3K2-2 Installation Instructions preview
D3K2-2
Brand: DYNATEK Pages: 4

Brands by name

Popular brands

Load more brands