Yamaha WR250F 2022 Owner'S Service Manual Download Page 22

Page: 22 / 404

BASIC SERVICE INFORMATION

1-10

EAM20120

BASIC SERVICE INFORMATION

EAM30181

ELECTRICAL SYSTEM

Electrical parts handling

NOTICE

ECA16600

Never disconnect a battery lead while the en-

gine is running; otherwise, the electrical

components could be damaged.

NOTICE

ECA16751

When disconnecting the battery leads from

the battery, be sure to disconnect the nega-

tive battery lead first, then the positive bat-

tery lead. If the positive battery lead is

disconnected first and a tool or similar item

contacts the vehicle, a spark could be gener-

ated, which is extremely dangerous.

TIP

If a battery lead is difficult to disconnect due to
rust on the battery terminal, remove the rust us-
ing hot water.

NOTICE

ECA16760

Be sure to connect the battery leads to the

correct battery terminals. Reversing the bat-

tery lead connections could damage the

electrical components.

NOTICE

ECA16771

When connecting the battery leads to the

battery, be sure to connect the positive bat-

tery lead first, then the negative battery lead.

If the negative battery lead is connected first

and a tool or similar item contacts the vehi-

cle while the positive battery lead is being

connected, a spark could be generated,

which is extremely dangerous.

NOTICE

ECA16620

Handle electrical components with special

care, and do not subject them to strong

shocks.

Summary of Contents for WR250F 2022





















































































































































































































































































































































































































Search results

Summary of Contents for WR250F 2022

Reviews:

Related manuals for WR250F 2022

Brands by name

Popular brands

Yamaha WR250F 2022, Owner'S Service Manual

Search results

Summary of Contents for WR250F 2022

Reviews:

Related manuals for WR250F 2022

Brands by name

Popular brands