manualshive.com logo in svg

Yamaha WR250F 2022, Owner'S Service Manual


Share
Download
background image

TROUBLESHOOTING

9-10

EAM30515

TROUBLESHOOTING OF STEERING/HANDLING

Rear suspension is soft

Oil leaking from rear shock 

absorber

Replace the rear shock absorber.

Gas leaking from rear shock 

absorber

Replace the rear shock absorber.

Fatigued or damaged rear shock 

absorber spring

Replace the rear shock absorber.

Improperly adjusted rear shock 

absorber spring preload (soft)

Adjust the spring preload.

Improperly adjusted rear shock 

absorber rebound damping (soft)

Adjust the rebound damping.

Improperly adjusted rear shock 

absorber compression damping 

(soft)

Adjust the compression damping.

Oil leaking from rear shock 

absorber

Bent, damaged, or corroded rear 

shock absorber rod

Replace the rear shock absorber.

Damaged oil seal lip

Replace the rear shock absorber.

Symptom

Possible cause

Actions

Handlebar wobble

Loose lower ring nut

Tighten the lower ring nut to the 

specified torque.

Worn bearing or bearing race

Replace the bearing and bearing 

race as a set.

Warped front fork

Repair or replace the front fork.

Bent front wheel axle

Replace the front wheel axle.

Incorrect tire pressure

Adjust to the specified tire pres-

sure.

Worn, deformed, or incorrect tire

Replace the tire.

Heavy steering

Lower ring nut is tightened too 

tight.

Tighten the lower ring nut to the 

specified torque.

Bent lower bracket

Replace the lower bracket.

Broken bearing or bearing race

Replace the bearing and bearing 

race as a set.

Incorrect tire pressure

Adjust to the specified tire pres-

sure.

Front wheel vibration

Loose spoke

Tighten the spoke and adjust the 

runout.

Damaged or worn wheel bearing

Replace the wheel bearing.

Worn, deformed, or incorrect tire

Replace the tire.

Loose wheel axle or wheel axle 

nut

Tighten the wheel axle or wheel 

axle nut to the specified torque.

Loose wheel axle pinch bolt

Tighten the wheel axle pinch bolt 

to the specified torque.

Incorrect front fork oil level

Adjust to the specified front fork oil 

level.

Symptom

Possible cause

Actions

Summary of Contents for WR250F 2022





















































































































































































































































































































































































































Reviews:

No comments

Related manuals for WR250F 2022

hepco & becker 6537581 00 01 Mounting Instructions preview
6537581 00 01
Brand: hepco & becker Pages: 5
Ducati 96480931A Manual preview
96480931A
Brand: Ducati Pages: 123
Takegawa 02-01-0284 Instruction Manual preview
02-01-0284
Brand: Takegawa Pages: 2
GAS GAS 2009 EC 200 2T Owner'S Manual preview
2009 EC 200 2T
Brand: GAS GAS Pages: 107
Two Brothers Racing 005-3860405-S1 Installation Instructions preview
005-3860405-S1
Brand: Two Brothers Racing Pages: 2
MSA Gallet F1 XF Operating Manual preview
Gallet F1 XF
Brand: MSA Pages: 168
R&G LP0127BK Fitting Instructions Manual preview
LP0127BK
Brand: R&G Pages: 11
R&G LP0197BK Fitting Instructions Manual preview
LP0197BK
Brand: R&G Pages: 14
X-lite X-501 Safety And Instructions For Use preview
X-501
Brand: X-lite Pages: 57
Yamaha TN359 Quick Start Manual preview
TN359
Brand: Yamaha Pages: 4
Yamaha FZR 600 Service Manual preview
FZR 600
Brand: Yamaha Pages: 12
Yamaha FZR600R Service Manual preview
FZR600R
Brand: Yamaha Pages: 40
Yamaha FZR600RB Supplementary Service Manual preview
FZR600RB
Brand: Yamaha Pages: 53
Yamaha FZ8 Owner'S Manual preview
FZ8
Brand: Yamaha Pages: 108
Yamaha FZ750 1987 Owner'S Manual preview
FZ750 1987
Brand: Yamaha Pages: 110
Yamaha FZ6RY Owner'S Manual preview
FZ6RY
Brand: Yamaha Pages: 110
Yamaha FZ6RD(C) Owner'S Manual preview
FZ6RD(C)
Brand: Yamaha Pages: 118
Yamaha FZ6RB Owner'S Manual preview
FZ6RB
Brand: Yamaha Pages: 116

Brands by name

Popular brands

Load more brands