Yamaha GRIZZLY 350 YFM35FGY Owner'S Manual Download | Manualshive

Page: 95 / 138

background image

8-17

8

NOTICE

ECB00420

Be sure no foreign material enters the final
gear case.

7. Install the oil filler bolt, and then tighten it to the

specified torque.

8. Check the final gear case for oil leakage. If oil

is leaking, check for the cause.

9. Install the final gear case guard by installing

the bolts and tightening them to the specified
torque.

EBU23433

Changing the differential gear oil

The differential gear case must be checked for oil
leakage before each ride. If any leakage is found,
have a Yamaha dealer check and repair the ATV.
In addition, the differential gear oil must be
changed as follows at the intervals specified in the
periodic maintenance and lubrication chart.

1. Place the ATV on a level surface.
2. Place an oil pan under the differential gear

case to collect the used oil.

1. Final gear oil
2. Final gear oil filler bolt

3. Correct oil level

Recommended final gear oil:

See page 10-1.

Tightening torque:

Final gear oil filler bolt:

23 Nm (2.3 m·kgf, 17 ft·lbf)

Tightening torque:

Final gear case guard bolt:

16 Nm (1.6 m·kgf, 11 ft·lbf)

U5UH65E0.book Page 17 Monday, June 16, 2008 10:34 AM

«
...
93
94
95
96
97
...
»

Summary of Contents for GRIZZLY 350 YFM35FGY











































































































































Reviews:

No comments

Related manuals for GRIZZLY 350 YFM35FGY

Brand: TrailMaster Pages: 13

Brand: Baja motorsports Pages: 82

Brand: Ardisam Pages: 8

Brand: Dinli Pages: 99

Brand: Suzuki Pages: 139

Brand: Can-Am Pages: 160

amphibious, off-road utility vehicle

Brand: Centaur Pages: 56

GP800Y WaveRunner GP

Brand: Yamaha Pages: 119

FxNytro FX10M53SZ

Brand: Yamaha Pages: 92

FX Nytro FX10MTRY

Brand: Yamaha Pages: 92

Brand: Yamaha Pages: 146

Brand: Yamaha Pages: 182

Brand: Yamaha Pages: 140

Brand: Baja motorsports Pages: 77

Brand: Yamaha Pages: 180

Brand: Kellfri Pages: 24

Brand: Yamaha Pages: 841

Grizzly 700 2011

Brand: Yamaha Pages: 172

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands