Yamaha GRIZZLY 350 YFM35FGY Owner'S Manual Download

Page: 109 / 138

8-31

Adjusting the brake lever free play

The brake lever free play should measure 3.0–5.0
mm (0.12–0.20 in) as shown. If the free play is in-
correct, adjust it as follows.

1. Loosen the locknut at the brake lever and fully

turn in the brake lever free play adjusting bolt.

2. Turn the brake lever free play adjusting nut on

the brake cable at the rear wheel hub so that
gap “A” measures 0–1 mm (0–0.04 in).

1. Brake pedal free play adjusting nut
2. Brake lever free play adjusting nut

1. Brake lever free play
2. Locknut

3. Brake lever free play adjusting bolt

U5UH65E0.book Page 31 Monday, June 16, 2008 10:34 AM

Summary of Contents for GRIZZLY 350 YFM35FGY











































































































































Search results

Summary of Contents for GRIZZLY 350 YFM35FGY

Reviews:

Related manuals for GRIZZLY 350 YFM35FGY

Brands by name

Popular brands

Yamaha GRIZZLY 350 YFM35FGY, Owner'S Manual

Search results

Summary of Contents for GRIZZLY 350 YFM35FGY

Reviews:

Related manuals for GRIZZLY 350 YFM35FGY

Brands by name

Popular brands