Yamaha GRIZZLY 350 YFM35FGY Owner'S Manual Download Page 96

Page: 96 / 138

8-18

3. Remove the differential gear oil filler bolt and

the differential gear oil drain bolt to drain the
oil from the differential gear case.

4. Install the drain bolt, and then tighten it to the

specified torque.

5. Refill with the specified amount of the recom-

mended differential gear oil.

TIP

●

Do not exceed the specified differential gear oil
quantity when filling. Overfilling will cause the oil
to seep out of the breather hose during and after
riding.

1. Differential gear oil filler bolt

1. Differential gear oil drain bolt

Tightening torque:

Differential gear oil drain bolt:

10 Nm (1.0 m·kgf, 7.2 ft·lbf)

U5UH65E0.book Page 18 Monday, June 16, 2008 10:34 AM

Summary of Contents for GRIZZLY 350 YFM35FGY











































































































































Search results

Summary of Contents for GRIZZLY 350 YFM35FGY

Reviews:

Brands by name

Popular brands

Yamaha GRIZZLY 350 YFM35FGY, Owner'S Manual

Search results

Summary of Contents for GRIZZLY 350 YFM35FGY

Reviews:

Brands by name

Popular brands