Yamaha GRIZZLY 350 YFM35FGY Owner'S Manual Download

Page: 99 / 138

8-21

6. Wash the sponge material gently but thor-

oughly in solvent.

WARNING

EWB01940

Always use parts cleaning solvent to clean the
sponge material. Never use low-flash-point
solvents or gasoline to clean the sponge mate-
rial because the engine could catch fire or ex-
plode.

7. Squeeze the excess solvent out of the sponge

material and let it dry.

NOTICE

ECB00440

Do not twist the sponge material when squeez-
ing it.

8. Check the sponge material and replace it if

damaged.

9. Apply a quality foam air filter oil to the sponge

material.

TIP

The sponge material should be wet but not drip-
ping.

10. Pull the sponge material over the air filter ele-

ment frame, and then install the lock plate.

1. Air filter element frame
2. Sponge material

3. Air filter element lock plate

U5UH65E0.book Page 21 Monday, June 16, 2008 10:34 AM

Summary of Contents for GRIZZLY 350 YFM35FGY











































































































































Search results

Summary of Contents for GRIZZLY 350 YFM35FGY

Reviews:

Related manuals for GRIZZLY 350 YFM35FGY

Brands by name

Popular brands

Yamaha GRIZZLY 350 YFM35FGY, Owner'S Manual

Search results

Summary of Contents for GRIZZLY 350 YFM35FGY

Reviews:

Related manuals for GRIZZLY 350 YFM35FGY

Brands by name

Popular brands