Yamaha GRIZZLY 350 YFM35FGY Owner'S Manual Download | Manualshive

Page: 107 / 138

background image

8-29

8

●

Refill with the same type of brake fluid. Mixing
fluids may result in a harmful chemical reaction
and lead to poor braking performance.

●

Be careful that water does not enter the brake
fluid reservoir when refilling. Water will signifi-
cantly lower the boiling point of the fluid and may
result in vapor lock.

●

Brake fluid may deteriorate painted surfaces or
plastic parts. Always clean up spilled fluid imme-
diately.

●

As the brake pads wear, it is normal for the brake
fluid level to gradually go down. However, if the
brake fluid level goes down suddenly, have a
Yamaha dealer check the cause.

EBU24281

Changing the brake fluid

Have a Yamaha dealer change the brake fluid at
the intervals specified in the TIP after the periodic
maintenance and lubrication chart. In addition,
have the oil seals of the brake master cylinder and
calipers as well as the brake hoses replaced at the
intervals listed below or whenever they are dam-
aged or leaking.

●

Oil seals: Replace every two years.

●

Brake hoses: Replace every four years.

EBU24393

Checking the front brake lever free play

The brake lever free play must be checked at the
intervals specified in the periodic maintenance and
lubrication chart. The brake lever should have no
free play as shown. If there is free play, have a
Yamaha dealer check the brake system.

WARNING

EWB02471

Operating with improperly serviced or adjust-
ed brakes could cause loss of braking ability,
which could lead to an accident.
After servicing:

1. Brake lever free play

U5UH65E0.book Page 29 Monday, June 16, 2008 10:34 AM

«
...
105
106
107
108
109
...
»

Summary of Contents for GRIZZLY 350 YFM35FGY











































































































































Reviews:

No comments

Related manuals for GRIZZLY 350 YFM35FGY

Brand: Tao Motor Pages: 80

Brand: LONCIN Pages: 65

Brand: KTM Pages: 190

Brand: NorAM Pages: 118

Brand: Kayo Pages: 4

Brand: Ace Sports Pages: 10

Brand: Yamaha Pages: 589

RAPTOR YFM700RF 2015

Brand: Yamaha Pages: 394

Brand: Yamaha Pages: 150

Brand: Suzuki Pages: 146

Brand: BERG Pages: 8

Brand: Ammann Pages: 170

Brand: Sno Jet Pages: 63

Brand: swaploader Pages: 93

Brand: swaploader Pages: 106

Brand: Massimo Pages: 103

Brand: Massimo Pages: 113

Brand: Massimo Pages: 158

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands