manualshive.com logo in svg

Yamaha GRIZZLY 350 YFM35FGY, Owner'S Manual

Share
Download
Yamaha GRIZZLY 350 YFM35FGY Owner'S Manual Download Page 97

8-19

8

●

The differential gear case capacity is greater
than the recommended oil quantity, therefore
the oil level cannot be accurately checked from
the oil filler hole.

NOTICE

ECB00410

Be sure no foreign material enters the differen-
tial gear case.

6. Install the oil filler bolt, and then tighten it to the

specified torque.

7. Check the differential gear case for oil leak-

age. If oil is leaking, check for the cause.

EBU23645

Cleaning the air filter element 

The air filter element should be cleaned at the in-
tervals specified in the periodic maintenance and
lubrication chart. Clean or, if necessary, replace
the air filter element more frequently if you are
riding in unusually wet or dusty areas.

TIP

There is a check hose at the bottom of the air filter
case. If dust or water collects in this hose, empty
the hose and clean the air filter element and air fil-
ter case.

1. Place the ATV on a level surface.

Recommended differential gear oil:

See page 10-1.

Oil quantity:

0.35 L (0.37 US qt, 0.31 Imp.qt)

Tightening torque:

Differential gear oil filler bolt:

23 Nm (2.3 m·kgf, 17 ft·lbf)

1. Air filter case check hose

U5UH65E0.book  Page 19  Monday, June 16, 2008  10:34 AM

Summary of Contents for GRIZZLY 350 YFM35FGY











































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands