Yamaha F40D Owner'S Manual Download Page 81

Page: 81 / 94

Maintenance

damage. Consult a Yamaha dealer for re-

pair of the lower unit seals.

NOTE:

For disposal of used oil, consult your

Yamaha dealer.

With the outboard motor in a vertical po-
sition, and using a flexible or pressur-
ized filling device, inject the gear oil into
the gear oil drain screw hole.

Put a new gasket on the oil level plug.
When the oil begins to flow out of the oil
level plug hole, insert and tighten the oil
level plug.

Put a new gasket on the gear oil drain
screw. Insert and tighten the gear oil
drain screw.

EMU29302

Cleaning fuel tank

WARNING

EWM00920

Gasoline is highly flammable, and its va-
pors are flammable and explosive.

●

If you have any question about properly
doing this procedure, consult your
Yamaha dealer.

●

Keep away from sparks, cigarettes,
flames, or other sources of ignition
when cleaning the fuel tank.

●

Remove the fuel tank from the boat be-
fore cleaning it. Work only outdoors in
an area with good ventilation.

●

Wipe up any spilled fuel immediately.

●

Reassemble the fuel tank carefully. Im-
proper assembly can result in a fuel
leak, which could result in a fire or ex-
plosion hazard.

●

Dispose of old gasoline according to lo-

cal regulations.

Empty the fuel tank into an approved
container.

Pour a small amount of suitable solvent
into the tank. Install the cap and shake
the tank. Drain the solvent completely.

Remove the screws holding the fuel joint
assembly. Pull the assembly out of the
tank.

Recommended gear oil:

Hypoid gear oil SAE#90

Gear oil quantity:

F40DET 430.0 cm

(14.54 US oz)

(15.17 Imp.oz)
F50FED 430.0 cm

(14.54 US oz)

(15.17 Imp.oz)
F50FET 430.0 cm

(14.54 US oz)

(15.17 Imp.oz)
F60CET 430.0 cm

(14.54 US oz)

(15.17 Imp.oz)
FT50GET 670.0 cm

(22.65 US oz)

(23.63 Imp.oz)
FT60DET 670.0 cm

(22.65 US oz)

(23.63 Imp.oz)

ZMU03274

Summary of Contents for F40D































































































Search results

Summary of Contents for F40D

Reviews:

Related manuals for F40D

Brands by name

Popular brands

Yamaha F40D, Owner'S Manual

Search results

Summary of Contents for F40D

Reviews:

Related manuals for F40D

Brands by name

Popular brands