Yamaha F40D Owner'S Manual Download Page 79

Page: 79 / 94

Maintenance

Checkpoints

●

Check each of the propeller blades for
wear, erosion from cavitation or ventila-
tion, or other damage.

●

Check the propeller shaft for damage.

●

Check the splines for wear or damage.

●

Check for fish line tangled around the pro-
peller shaft.

●

Check the propeller shaft oil seal for dam-
age.

EMU30661

Removing propeller

EMU29195

Spline models

Straighten the cotter pin and pull it out
using a pair of pliers.

Remove the propeller nut, washer, and
spacer (if equipped).

Remove the propeller and thrust wash-
er.

EMU30671

Installing propeller

EMU29231

Spline models

CAUTION:

ECM00340

●

Be sure to install the thrust washer be-

ZMU01897

1. Cotter pin
2. Propeller nut
3. Washer
4. Spacer
5. Propeller
6. Thrust washer

ZMU03228

Summary of Contents for F40D































































































Search results

Summary of Contents for F40D

Reviews:

Related manuals for F40D

Brands by name

Popular brands

Yamaha F40D, Owner'S Manual

Search results

Summary of Contents for F40D

Reviews:

Related manuals for F40D

Brands by name

Popular brands