Yamaha F40D Owner'S Manual Download Page 63

Page: 63 / 94

Maintenance

DPR6EB-9

Spark plug gap:

0.8–0.9 mm (0.031–0.035 in)

Control system:

Remote control

Starting system:

Electric

Starting carburetion system:

Electronic fuel injection

Valve clearance (cold engine) IN:

0.15–0.25 mm (0.0059–0.0098 in)

Valve clearance (cold engine) EX:

0.25–0.35 mm (0.0098–0.0138 in)

Min. cold cranking amps (CCA/EN):

430.0 A

Min. rated capacity (20HR/IEC):

70.0 Ah

Maximum generator output:

17.0 A

Drive unit:

Gear positions:

Forward-neutral-reverse

Gear ratio:

F40DET 1.85 (24/13)
F50FED 1.85 (24/13)
F50FET 1.85 (24/13)
F60CET 1.85 (24/13)
FT50GET 2.33 (28/12)
FT60DET 2.33 (28/12)

Trim and tilt system:

F40DET Power trim and tilt
F50FED Hydro tilt
F50FET Power trim and tilt
F60CET Power trim and tilt
FT50GET Power trim and tilt
FT60DET Power trim and tilt

Propeller mark:

F40DET G
F50FED G
F50FET G
F60CET G

FT50GET K
FT60DET K

Fuel and oil:

Recommended fuel:

Regular unleaded gasoline

Min. research octane:

Fuel tank capacity:

25 L (6.60 US gal) (5.50 Imp.gal)

Recommended engine oil:

4-stroke outboard motor oil

Recommended engine oil group 1*:

SAE 10W-30/10W-40/5W-30
API SE/SF/SG/SH/SJ/SL

Recommended engine oil group 2*:

SAE 15W-40/20W-40/20W-50
API SH/SJ/SL

Lubrication:

Wet sump

Engine oil quantity (excluding oil filter):

2.5 L (2.64 US qt) (2.20 Imp.qt)

Recommended gear oil:

Hypoid gear oil SAE#90

Gear oil quantity:

F40DET 430.0 cm

(14.54 US oz)

(15.17 Imp.oz)
F50FED 430.0 cm

(14.54 US oz)

(15.17 Imp.oz)
F50FET 430.0 cm

(14.54 US oz)

(15.17 Imp.oz)
F60CET 430.0 cm

(14.54 US oz)

(15.17 Imp.oz)
FT50GET 670.0 cm

(22.65 US oz)

(23.63 Imp.oz)
FT60DET 670.0 cm

(22.65 US oz)

(23.63 Imp.oz)

Tightening torque for engine:

Spark plug:

18.0 Nm (13.3 ft-lb) (1.84 kgf-m)

Propeller nut:

35.0 Nm (25.8 ft-lb) (3.57 kgf-m)

Summary of Contents for F40D































































































Search results

Summary of Contents for F40D

Reviews:

Related manuals for F40D

Brands by name

Popular brands

Yamaha F40D, Owner'S Manual

Search results

Summary of Contents for F40D

Reviews:

Related manuals for F40D

Brands by name

Popular brands