Yamaha F40D Owner'S Manual Download Page 28

Page: 28 / 94

Basic components

EMU31703

Fuel filter/Water separator

This engine has a combination fuel filter/wa-
ter separator and associated warning sys-
tem. If water separated from the fuel
exceeds a specific volume, the warning de-
vice of Command Link Tachometer will acti-
vate.

Activation of warning device

●

The water separator-warning indicator of
Command Link Tachometer will blink.

●

The buzzer will sound intermittently only
when the gear shift is in neutral.

●

If the warning system has activated, stop
the engine and consult a Yamaha dealer
immediately.

EMU26302

Warning indicator

If the engine develops a condition which is

cause for warning, the indicator lights up. For
details on how to read the warning indicator,
see page 33.

EMU26470

Tachometer

This gauge shows the engine speed and has
the following functions.

EMU26491

Digital tachometer

The tachometer shows the engine speed
and has the following functions.

NOTE:

All segments of the display will light momen-
tarily after the main switch is turned on and

will return to normal thereafter.

1. Flushing device

ZMU05095

ZMU05474

1. Warning indicator

1. Tachometer
2. Warning indicator(s)

ZMU04578

Summary of Contents for F40D































































































Search results

Summary of Contents for F40D

Reviews:

Related manuals for F40D

Brands by name

Popular brands

Yamaha F40D, Owner'S Manual

Search results

Summary of Contents for F40D

Reviews:

Related manuals for F40D

Brands by name

Popular brands