Yamaha F40D Owner'S Manual Download Page 36 | Manualshive

Page: 36 / 94

background image

Basic components

30

overheat-warning indicator blinks. Seri-
ous engine damage will occur.

●

Do not continue to operate the engine if
a warning device has activated. Con-
sult your Yamaha dealer if the problem

cannot be located and corrected.

Water separator warning

This indicator will blink when water has accu-
mulated in the water separator (fuel filter)
while cruising. In such an event, stop the en-
gine immediately and see page 83 of this
manual to drain the water from the fuel filter.
Get back to the port soon and consult a
Yamaha dealer immediately.

CAUTION:

ECM00910

Gasoline mixed with water could cause

damage to the engine.

Engine trouble warning

This indicator will blink when the engine mal-

functions while cruising. Get back to the port
soon and consult a Yamaha dealer immedi-
ately.

CAUTION:

ECM00920

In such an event, the engine will not oper-
ate properly. Consult a Yamaha dealer

immediately.

Low battery voltage warning

When the battery voltage drops, the low bat-
tery voltage-warning indicator and the bat-
tery voltage value will start to blink. Get back
to the port soon if the low battery voltage-
warning device has activated. For charging
the battery, consult your Yamaha dealer.

ZMU05423

ZMU05424

ZMU05425

ZMU05426

«
...
34
35
36
37
38
...
»

Summary of Contents for F40D































































































Reviews:

No comments

Related manuals for F40D

PIC18F57Q43 Curiosity Nano

Brand: Microchip Technology Pages: 34

Brand: Gigabyte Pages: 100

Brand: Avalue Technology Pages: 89

TA870 PLUS - SETUP 2

Brand: Biostar Pages: 67

Brand: BESTEK Pages: 52

IMBA-G412ISA-R20

Brand: IEI Technology Pages: 164

Brand: ECS Pages: 60

Brand: Quantum Design Pages: 77

Brand: IEI Technology Pages: 162

MAG Z490 TOMAHAWK

Brand: MSI Pages: 76

Brand: Yamaha Pages: 114

Brand: NXP Semiconductors Pages: 12

Brand: BCM Pages: 93

Brand: Gigabyte Pages: 37

Brand: MSI Pages: 85

Brand: Gigabyte Pages: 96

Brand: Supermicro Pages: 84

Brand: Octek Pages: 102

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands