background image

 

Safety information

 

7

 

EMU33900

 

Carbon monoxide

 

This product emits exhaust gases which
contain carbon monoxide, a colorless, odor-
less gas which may cause brain damage or
death when inhaled. Symptoms include nau-
sea, dizziness, and drowsiness. Keep cock-
pit and cabin areas well ventilated. Avoid
blocking exhaust outlets.

 

EMU33780

 

Modifications

 

Do not attempt to modify this outboard mo-
tor. Modifications to your outboard motor
may reduce safety and reliability, and render
the outboard unsafe or illegal to use.

 

EMU33740

 

Boating safety

 

This section includes a few of the many im-
portant safety precautions that you should
follow when boating.

 

EMU33710

 

Alcohol and drugs

 

Never operate after drinking alcohol or tak-
ing drugs. Intoxication is one of the most
common factors contributing to boating fatal-
ities.

 

EMU33720

 

Personal flotation devices

 

Have an approved personal flotation device
(PFD) on board for every occupant. Yamaha
recommends that you must wear a PFD
whenever boating. At a minimum, children
and non-swimmers should always wear
PFDs, and everyone should wear PFDs
when there are potentially hazardous boat-
ing conditions.

 

EMU33730

 

People in the water

 

Always watch carefully for people in the wa-
ter, such as swimmers, skiers, or divers,
whenever the engine is running. When
someone is in the water near the boat, shift

into neutral and shut off the motor.
Stay away from swimming areas. Swimmers
can be hard to see.
The propeller can keep moving even when
the motor is in neutral. Shut off the engine
when a person is in the water near you.

 

EMU33750

 

Passengers

 

Consult your boat manufacturer’s instruc-
tions for details about appropriate passenger
locations in your boat and be sure all pas-
sengers are positioned properly before ac-
celerating and when operating above an idle
speed. Standing or sitting in non-designated
locations may result in being thrown either
overboard or within the boat due to waves,
wakes, or sudden changes in speed or direc-
tion. Even when people are positioned prop-
erly, alert your passengers if you must make
any unusual maneuver. Always avoid jump-
ing waves or wakes.

 

EMU33760

 

Overloading

 

Do not overload the boat. Consult the boat
capacity plate or boat manufacturer for max-
imum weight and number of passengers. Be
sure that weight is properly distributed ac-
cording to the boat manufacturers instruc-
tions. Overloading or incorrect weight
distribution can compromise the boats han-
dling and lead to an accident, capsizing or
swamping.

 

EMU33770

 

Avoid collisions

 

Scan constantly

 

 for people, objects, and

other boats. Be alert for conditions that limit
your visibility or block your vision of others.

 

Operate defensively

 

 at safe speeds and

keep a safe distance away from people, ob-
jects, and other boats.

 

 

Do not follow directly behind other boats or
waterskiers.

Summary of Contents for F40D































































































Reviews: