Yamaha F40D Owner'S Manual Download Page 59

Page: 59 / 94

Operation

EMU28175

Procedure for hydro tilt models

Place the remote control lever / gear
shift lever in neutral.

Pull the tilt lock lever up to the release
position.

Slightly tilt the outboard motor up to the
desired position and push the tilt lock le-
ver down to the lock position.

To return the outboard motor to the nor-
mal running position, pull the tilt lock le-

ver up to the release position and slowly
tilt the outboard motor down.

Push the tilt lock lever down to the lock
position.

EMU32850

Power trim and tilt models models

The outboard motor can be tilted up partially
to allow operation in shallow water.

WARNING

EWM00660

●

Place the gear shift in neutral before
setting up for shallow water cruising.

●

Return the outboard motor to its normal
position as soon as the boat is back in

deeper water.

CAUTION:

ECM00260

Do not tilt the outboard motor up so that
the cooling water inlet on the lower unit is
above the surface of the water when set-
ting up for and cruising in shallow water.
Otherwise severe damage from overheat-

ing can result.

EMU32910

Procedure for power trim and tilt

Place the remote control lever / gear
shift lever in neutral.

ZMU03087

ZMU03647

ZMU03648

Summary of Contents for F40D































































































Search results

Summary of Contents for F40D

Reviews:

Related manuals for F40D

Brands by name

Popular brands

Yamaha F40D, Owner'S Manual

Search results

Summary of Contents for F40D

Reviews:

Related manuals for F40D

Brands by name

Popular brands