Yamaha F20G Page 99 Owner'S Manual Download

Page: 99 / 108

Trouble Recovery

Water pump

Is water pump malfunctioning?

Have serviced by a Yamaha dealer.

Fuel filter

Is there excess water in fuel filter?

Drain fuel filter.

Trouble

Engine power loss.

Item

Question

Answer

Propeller

Is propeller damaged?

Have propeller repaired or replaced.

Is propeller pitch or diameter incor-
rect?

Install correct propeller to operate
outboard motor at its recommended
speed (r/min) range.

Mounting height

Is outboard motor mounted at incor-
rect height on transom?

Have outboard motor adjusted to
proper transom height.

Alert system

Has alert system activated?

Find and correct cause of alert.

Boat bottom

Is boat bottom fouled with marine
growth?

Clean boat bottom.

Spark plugs

Are spark plugs fouled or of incorrect
type?

Inspect spark plugs. Clean or replace
with recommended type.

Is spark plug gap incorrect?

Replace spark plug.

Is heat range of spark plugs incor-
rect?

Inspect spark plugs and replace with
recommended type.

Lower unit

Are weeds or other foreign material
tangled on gear housing?

Remove foreign material and clean
lower unit.

Fuel system

Is fuel system clogged?

Inspect for pinched or kinked fuel line
or other obstructions in fuel system.

Fuel filter

Is fuel filter clogged?

Clean or replace fuel filter.

Fuel

Is fuel contaminated or stale?

Fill tank with clean, fresh fuel.

Is specified fuel not being used?

Replace fuel with specified type

Ignition wiring

Is ignition wiring damaged or poorly
connected?

Inspect wires for breaks and wear.
Have connections tightened and bro-
ken or worn wires replaced by a
Yamaha dealer.

Electrical parts

Are electrical parts malfunctioning?

Have serviced by a Yamaha dealer.

Engine oil

Is specified engine oil not being
used?

Replace engine oil with specified
type.

Thermostat

Is thermostat clogged or malfunction-
ing?

Have serviced by a Yamaha dealer.

Fuel tank

Is fuel tank air vent restricted or
clogged?

Remove obstruction.

Fuel pump

Is fuel pump malfunctioning?

Have serviced by a Yamaha dealer.

Fuel joint

Is fuel joint connection incorrect?

Connect correctly.

Gear shift lever

Is engine not responding properly to
gear shift lever position?

Have serviced by a Yamaha dealer.

Trouble

Alert buzzer sounds or indicator lights.

Item

Question

Answer

6HY-9-71-1E0.book 93 ページ２０１９年１２月４日　水曜日　午後２時５１分

Summary of Contents for F20G













































































































Search results

Summary of Contents for F20G

Reviews:

Related manuals for F20G

Brands by name

Popular brands

Yamaha F20G, Owner'S Manual

Search results

Summary of Contents for F20G

Reviews:

Related manuals for F20G

Brands by name

Popular brands