Yamaha F20G Owner'S Manual Download

Page: 69 / 108

Operation

EMU28126

Procedure

(1) Place the remote control lever / gear

shift lever in neutral.

(2) Place the tilt lock lever in the release/up

position.

(3) Slightly tilt the outboard motor up. The

tilt support bar will lock automatically,
supporting the outboard motor in a par-
tially raised position. This outboard mo-
tor has 2 positions for shallow water
cruising.

(4) To return the outboard motor to the nor-

mal running position, place the remote
control lever / gear shift lever in neutral.

(5) Place the tilt lock lever in the lock/down

position, then slightly tilt the outboard
motor up until the tilt support bar auto-
matically returns to the free position.

ZMU03087

ZMU0

756

ZMU08808

ZMU08769

6HY-9-71-1E0.book 63 ページ２０１９年１２月４日　水曜日　午後２時５１分

Summary of Contents for F20G













































































































Search results

Summary of Contents for F20G

Reviews:

Related manuals for F20G

Brands by name

Popular brands

Yamaha F20G, Owner'S Manual

Search results

Summary of Contents for F20G

Reviews:

Related manuals for F20G

Brands by name

Popular brands