Yamaha F20G Owner'S Manual Download | Manualshive

Page: 38 / 108

background image

32

Instruments and indicators

EMU36016

Indicators

EMU36026

Low oil pressure-alert indicator

If oil pressure drops too low, this indicator will
light up. For further information, see page 33.

ECM00024



Do not continue to run the engine if the
low oil pressure-alert indicator is on
and the engine oil level is lower. Seri-
ous engine damage will occur.



The low oil pressure-alert indicator
does not indicate the engine oil level.
Use the oil dipstick to check the oil lev-
el. For further information, see page 41.

EMU36034

Overheat-alert indicator

If the engine temperature rises too high, this
indicator will light up. For further information
on reading the indicator, see page 33.

ECM00053

Do not continue to run the engine if the
overheat-alert indicator is on. Serious en-
gine damage will occur.

1. Low oil pressure-alert indicator

1. Low oil pressure-alert indicator

1

ZMU0

8

741

1

1. Overheat-alert indicator

1. Overheat-alert indicator

1

ZMU0

8

742

1

6HY-9-71-1E0.book 32 ページ２０１９年１２月４日　水曜日　午後２時５１分

«
...
36
37
38
39
40
...
»

Summary of Contents for F20G













































































































Reviews:

No comments

Related manuals for F20G

Brand: Quectel Pages: 34

Brand: ST Pages: 77

Brand: Gigabyte Pages: 104

DQ45CB - Desktop Board Executive Series Motherboard

Brand: Intel Pages: 96

Brand: Supero Pages: 77

Brand: Supermicro Pages: 147

Brand: Microchip Technology Pages: 30

Super 7 SY-5SSM

Brand: SOYO Pages: 86

STEVAL-IHM022V1

Brand: ST Pages: 58

Brand: Yamaha Pages: 120

Brand: Yamaha Pages: 118

Brand: Yamaha Pages: 124

Brand: Yamaha Pages: 122

Brand: Yamaha Pages: 125

Brand: Yamaha Pages: 124

Brand: Yamaha Pages: 122

Brand: Yamaha Pages: 98

Brand: Micrel Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands