Yamaha F20G Owner'S Manual Download

Page: 48 / 108

Operation

board motor is not level, the oil level
indicated on the oil dipstick may not
be accurate.

[ECM01862]

(2) Remove the oil dipstick and wipe it

clean.

(3) Insert the oil dipstick completely and re-

move it again.

(4) Check that the oil level on the oil dipstick

is between the upper and lower marks.
Consult your Yamaha dealer if the oil
level is not at the proper level or if it ap-
pears milky or dirty.

EMU27154

Engine



Check the engine and engine mounting.



Look for loose or damaged fasteners.



Check the propeller for damage.



Check for engine oil leaks.

EMU36494

Flushing device

Check that the flushing device’s garden hose
connector is securely screwed on to the fit-
ting on the bottom cowling.

NOTICE:

If the

garden hose connector is not properly
connected, cooling water can leak out
and the engine can overheat during oper-
ation.

[ECM01802]

EMU36956

Install top cowling

(1) Be sure that the cowling lock lever is re-

leased.

(2) Be sure that the rubber seal is seated all

the way around the top cowling.

1. Oil dipstick

1. Oil dipstick
2. Lower mark
3. Upper mark

ZMU0

751

ZMU08752

1. Fitting
2. Flushing device

ZMU08753

6HY-9-71-1E0.book 42 ページ２０１９年１２月４日　水曜日　午後２時５１分

Summary of Contents for F20G













































































































Search results

Summary of Contents for F20G

Reviews:

Related manuals for F20G

Brands by name

Popular brands

Yamaha F20G, Owner'S Manual

Search results

Summary of Contents for F20G

Reviews:

Related manuals for F20G

Brands by name

Popular brands