Yamaha F20G Owner'S Manual Download

Page: 15 / 108

General information

EMU33913

Contents of labels

The above warning labels mean as follows.

EWM01692

Emergency starting does not have start-
in-gear protection. Ensure shift control is
in neutral before starting engine.

EWM01682



Keep hands, hair, and clothing away
from rotating parts while the engine is
running.



Do not touch or remove electrical parts
when starting or during operation.

EWM01672



Read Owner’s Manuals and labels.



Wear an approved personal flotation
device (PFD).



Attach engine shut-off cord (lanyard) to
your PFD, arm, or leg so the engine
stops if you accidentally leave the
helm, which could prevent a runaway
boat.

ZMU05746

6EE-G2794-40

6EE-G2794-50

6EE-H1994-40

6EE-H1994-50

6EE-H1995-40

6EE-H1995-50

6HY-9-71-1E0.book 9 ページ２０１９年１２月４日　水曜日　午後２時５１分

Summary of Contents for F20G













































































































Search results

Summary of Contents for F20G

Reviews:

Related manuals for F20G

Brands by name

Popular brands

Yamaha F20G, Owner'S Manual

Search results

Summary of Contents for F20G

Reviews:

Related manuals for F20G

Brands by name

Popular brands