manualshive.com logo in svg

Yamaha 4X4 BIG BEAR PROFESSIONAL, Owner'S Manual, Page: 122 / 172

Share
Download
Yamaha 4X4 BIG BEAR PROFESSIONAL Owner'S Manual Download Page 122

8-11

EBU00706

Differential gear oil
Differential gear oil measurement

1. Place the machine on a level place.
2. Remove the oil filler bolt and check the oil

level. It should be up to the brim of the
hole. If the level is low, add sufficient oil to
raise it to the specified level.

CAUTION:

_ 

Be sure no foreign material enters the dif-
ferential gear case. 

_

1. Filler bolt

3. Install the oil filler bolt and tighten it to the

specified torque.

Differential gear oil replacement

1. Place the machine on a level place.
2. Place a container under the differential

gear case to catch the oil.

3. Remove the filler bolt and drain bolt to

drain the oil.

1. Drain bolt

Tightening torque:

Oil filler bolt:

12 Nm (1.2 m·kgf, 8.7 ft·lbf)

U5FU13.book  Page 11  Wednesday, April 24, 2002  11:02 AM

Summary of Contents for 4X4 BIG BEAR PROFESSIONAL













































































































































































Reviews:

No comments