Xylem CentiPro Aquavar IPC Application Manual Download Page 35 | Manualshive

Page: 35 / 36

background image

PAGE 35

Aquavar IPC Start-Up Genie

CentriPro

AQUAVAR IPC Q&A (AQIPCQA)

26. QUESTION

I am missing my terminal blocks and other
connectors.

26. ANSWER

The connectors and terminal blocks are shipped in
a separate accessory bag in the envelope. These
terminal blocks are left off during production for
final validation testing in the factory. They do not
ship without the terminal connectors. If you cannot
locate your accessory bag, you can order your
terminal blocks using the part numbers below.
Please order from your frame size.

9K686

Accessory Bag Frame Size A2

9K687

Accessory Bag Frame Size A5

9K688

Accessory Bag Frame Size B1

9K689

Accessory Bag Frame Size B2

9K690

Accessory Bag Frame Size B3

9K691

Accessory Bag Frame Size B4

9K692

Accessory Bag Frame Size B4 Large

9K693

Accessory Bag Frame Size C1

9K694

Accessory Bag Frame Size C2

9K695

Accessory Bag Frame Size C3

9K696

Accessory Bag Frame Size C4 Small

9K697

Accessory Bag Frame Size C4 Large

27. QUESTION

I have a Duplex setup and my lag pump runs at Full
Speed constantly.

27. ANSWER

Please verify that your dip switches are set correctly
on both drives. A54 controls the Lag pump. Please
refer to the IPC Duplex Troubleshooting Guide -
IM290R00.

28. QUESTION

I am getting the A60-interlock fault.

28. ANSWER

You incorrectly setup your digital input #27 for
pump protection during the startup. Go into menu
5-12 and change to (0) no operation.

«
...
33
34
35
36
»

Summary of Contents for CentiPro Aquavar IPC





































Reviews:

No comments

Related manuals for CentiPro Aquavar IPC

FPBA-01 PROFIBUS DP

Brand: ABB Pages: 2

ControlMaster CM15

Brand: ABB Pages: 4

Brand: Samson Pages: 100

Brand: Danfoss Pages: 16

Brand: Radio Shack Pages: 3

Brand: jbc Pages: 4

Brand: Parker Pages: 28

Brand: Keba Pages: 16

Brand: KEB Pages: 16

Brand: OJ Electronics Pages: 8

infi 90 IMMFP12

Brand: Bailey Pages: 75

iSteam 2.0 Control

Brand: mr. steam Pages: 16

Brand: Sygonix Pages: 12

Brand: Multi-Clean Pages: 4

Brand: Primo Water Pages: 10

Brand: PENGWYN Pages: 32

Brand: Warner Electric Pages: 6

DIGITAL EPIC-2 DTM

Brand: Westlock Pages: 33

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands