background image

5015T Flat Panel Industrial Monitor                                                                                                 Chapter 2 Installation 

15 

142029 (D)

 

2.  If present, keep enclosure doors or openings closed at all times, to avoid the 

accumulation of foreign matter inside the workstation. 

 
3.  Never subject the unit to any installation or service procedures unless power is 

removed and the area is known to be non-hazardous. This includes the installation or 

removal of power cables, communication cables, or removal of the rear cover of the 

unit. 

Only technically qualified service personnel should perform all installation and service. 

These workstations are designed to require no service in the course of normal operation 

by an operator. 

Safety Agency Approval 

The Xycom Automation systems are designed to meet the following standards: 

• 

Underwriters Laboratories Inc., UL 1604 Standard for Safety 

Electrical equipment for use in Class I and Class II, Division 2, locations 

• 

Underwriters Laboratories Inc., UL 60950, Information Technology Equipment 

• 

Canadian Standard Association, Specification C22.2 No. 213-M1987 

Non-incendiary electrical equipment for use in Class I, Division 2 hazardous 

locations 

• 

Canadian Standards Association, Specification C22.2 No. 950 

Information Technology Equipment 

• 

EN 60950, Information Technology Equipment 

 

Summary of Contents for 5015T






























Reviews: