Xtrails VESDA-E VEP-A00 Product Manual Download Page 71

Page: 71 / 109

VESDA-E VEP-A00-P Product Guide

www.xtralis.com

Function

State Change

Mains OK

Unmonitored GPI

The detector reports “Power Supply
AC Input Failure” (fault 761) when ≤ 2
VDC.

The detector does not report “Power
Supply AC Input Failure” (fault 761)
when ≥ 5 VDC.

Monitored GPI

The detector does not report “Power
Supply AC Input Failure” (fault 761)
while the contact is open.

The detector reports “Power Supply
AC Input Failure” (fault 761) while the
contact is closed.

Refer to Figure 4-38 in Section 4.3.10 on
page 39 and Section 4.3.11 on page 39 for
further information.

Fault 761

Open

Closed

Fault 761

Standby Mode

Unmonitored GPI

The detector is held in Standby mode
(see Section 7.1) while ≥ 5 VDC.

The detector exits Standby mode at a
5 VDC to 0 VDC falling edge.

Monitored GPI

The detector is held Standby mode
(see Section 7.1) while contact is
closed.

The detector exits Standby mode
when the contact opens.

Note:

No alarms can be generated
while the detector is in standby
mode.

Standby

Open

Closed

Enabled

Standby

Reset

Enabled

Reset

Disable

Unmonitored GPI

The detector is held disabled while ≥
5 VDC.

The detector is enabled on a 5 VDC
to 0 VDC falling edge.

Monitored GPI

The detector is held disabled while
contact is closed.

The detector is enabled when the
contact opens.

Note:

No alarms are signalled while
the detector is disabled.

Disabled

Enabled

Open

Closed

Disabled

Enabled

Table 5-3: GPI Operation (continued...)

Summary of Contents for VESDA-E VEP-A00














































































































Search results

Summary of Contents for VESDA-E VEP-A00

Reviews:

Related manuals for VESDA-E VEP-A00

Brands by name

Popular brands

Xtrails VESDA-E VEP-A00, Product Manual

Search results

Summary of Contents for VESDA-E VEP-A00

Reviews:

Related manuals for VESDA-E VEP-A00

Brands by name

Popular brands