Xtrails VESDA-E VEP-A00 Product Manual Download | Manualshive

Page: 4 / 109

background image

VESDA-E VEP-A00-P Product Guide

ii

www.xtralis.com

Scope

The VESDA-E VEP-A00 Product Guide provides a comprehensive description of the VESDA-E VEP-A00
detector and its accessories.

This guide introduces the VEP-A00 features, technical specifications and gives an understanding of its
components and their function. You will also find instructions on installing, cabling and powering up the
detector.

This guide is for anyone involved with the design, maintenance and purchasing of a VESDA-E system. It is
assumed that anyone using this product has the knowledge and appropriate certification from local fire and
electrical authorities.

Document Conventions

The following typographic conventions are used in this document:

Convention Description

Bold

Used to denote:

emphasis.

Used for names of menus, menu options, toolbar buttons

Italics

Used to denote:

references to other parts of this document or other

documents. Used for the result of an action.

The following icons are used in this document:

Convention Description

Caution:

This icon is used to indicate that there is a danger to

equipment. The danger could be loss of data, physical damage, or
permanent corruption of configuration details.

Warning:

This icon is used to indicate that there is a danger of electric

shock. This may lead to death or permanent injury.

Warning:

This icon is used to indicate that there is a danger of inhaling

dangerous substances. This may lead to death or permanent injury.

Contact Us

UK and Europe

+44 1442 242 330

The Americas

+1 800 229 4434

Middle East

+962 6 588 5622

Asia

+86 10 56697101

Australia and New Zealand

+61 3 9936 7000

www.xtralis.com

«
...
2
3
4
5
6
...
»

Summary of Contents for VESDA-E VEP-A00














































































































Reviews:

No comments

Related manuals for VESDA-E VEP-A00

Brand: La Crosse Technology Pages: 18

Brand: TEC Electronics Pages: 16

Brand: Majestic Pages: 8

Brand: Pure Acoustics Pages: 10

Brand: Life Pages: 4

Brand: Jenile Pages: 14

Samurai CS-8801SE

Brand: CrimeStopper Pages: 11

Brand: Subaru Pages: 26

Brand: OttLite Pages: 53

Brand: Concept Smoke Screen Pages: 8

Brand: AEG Pages: 28

Brand: AEG Pages: 48

Brand: AEG Pages: 46

SRC 4331 CD/MP3

Brand: AEG Pages: 64

Brand: AEG Pages: 122

Brand: Philips Pages: 2

digital fork thermometer

Brand: Andrew James Pages: 5

Brand: Volvo Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands