Xtrails VESDA-E VEP-A00 Product Manual Download | Manualshive

Page: 60 / 109

background image

VESDA-E VEP-A00-P Product Guide

52

www.xtralis.com

5.4

Commands

The following commands are able to be issued to the detector. As indicated below in Table 5-2, a small
number of basic commands can be executed from the detector via buttons, while the full range of commands
can be executed using the Xtralis VSC software.

Command

Description

Execute From

A button

on the

Detector

Xtralis VSC

Software

Disable (Isolate)

The Disable command disables all the output relays
associated with the detector. The aspirator remains
active.

Enable

The Enable command enables all of the output
relays associated with the detector.

Go to Standby

The Go to Standby sets the detector to Standby
mode. See Section 7.1 on page 71 for a description
of Standby mode.

End Standby

The End Standby command is available when the
detector is in Standby mode. The End Standby
command causes the detector to exit Standby
mode.

Reset

The Reset command unlatches all latched alarms
and faults, and returns relays to their normal state.
Clears the Xtralis VSC active event list.

Reset does not enable a disabled detector or
reactivate a detector that is in Standby mode.

Start Normalize Air Flow Starts the air flow normalization process for the

selected detector.

The normalization process determines the reference
flow rate.

The detector can be in normal or disabled mode, but
not standby mode.

The aspirator remains on throughout the
normalization process and no fault is reported unless
the process fails to successfully complete.

The normalizing status may be observed on the
"detailed status" tab in the Xtralis VSC software.

To normalize the detector using the internal
AutoConfig button, press and hold the button until
the AutoConfig LED illuminates, then release the
button. To cancel the normalization process, press
and hold the button for 5 seconds. The LED will turn
off.

Table 5-2: Detector Commands

«
...
58
59
60
61
62
...
»

Summary of Contents for VESDA-E VEP-A00














































































































Reviews:

No comments

Related manuals for VESDA-E VEP-A00

Brand: Southern Pride Pages: 2

Brand: La Crosse Technology Pages: 9

Brand: Uniden Pages: 8

Bandit CM160-367

Brand: Charmate Pages: 12

Brand: Prestige Pages: 20

Brand: TFA Pages: 2

Brand: TFA Pages: 50

Brand: Bellman & Symfon Pages: 27

LaserSCANNER VLS-200

Brand: VESDA Pages: 27

Brand: VESDA Pages: 48

Brand: VESDA Pages: 64

Brand: CrimeStopper Pages: 1

Brand: Equity Pages: 2

Brand: Venturer Pages: 2

Brand: Vision Pages: 3

Brand: Abus Pages: 80

Brand: Abus Pages: 234

Brand: olympia electronics Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands