Xtrails VESDA-E VEP-A00 Product Manual Download | Manualshive

Page: 7 / 109

background image

VESDA-E VEP-A00-P Product Guide

www.xtralis.com

v

Product Security Advice

Warning:

Failure to comply with the requirements below exposes the system to malicious interference
which could disable smoke reporting.

Scan the QR code to access the latest security advice available from: https://xtralis.com/33252

Commissioning Requirements

l

All VESDAnet wiring and connection ports must be secured against unauthorized access.

l

Ethernet and Wi-Fi ports must ONLY be connected to networks which are secure and physically or
logically separate from business IT infrastructure.

l

VESDA devices including HLIs must not be accessible from the Internet. Any provision of remote
access to VESDA devices must be subjected to a full cyber security risk assessment and regular
review.

l

WPA-2 encryption must be used whenever Wi-Fi is enabled.

l

Restrict access to HLI devices to authorized personnel only.

l

Passwords must be chosen in line with the guidelines in the detector user guide and provided to trusted
users only.

l

Default PIN codes must be changed as part of the initial configuration.

System Maintenance Requirements

l

Do NOT use the USB port for long-term monitoring or allow it to be permanently wired to building
infrastructure. It is only to be used for configuration and maintenance by authorized personnel.

l

If a detector requires firmware upgrade, ensure that the upgrade package is genuine and obtained directly
from Xtralis.

l

Access to PCs on which VSC or VSM configuration software and system configuration information are
installed must be restricted to authorized persons if saved passwords are used.

l

Xtralis PC software such as VSC or VSM, must only be installed on PCs with current active Windows
support from Microsoft.

«
...
5
6
7
8
9
...
»

Summary of Contents for VESDA-E VEP-A00














































































































Reviews:

No comments

Related manuals for VESDA-E VEP-A00

4706X Responder LC3

Brand: Clifford Pages: 57

Brand: Masterbuilt Pages: 52

Brand: La Crosse Technology Pages: 5

Brand: Dynatech Pages: 9

LIFESAVER silhouette 5800ACF

Brand: PSA Products Pages: 2

Prestige APS-15R

Brand: Audiovox Pages: 19

Prestige Platinum 128-4629B

Brand: Audiovox Pages: 21

Brand: Prestige Pages: 20

Brand: Giant Alarm System Pages: 3

Brand: Equity Pages: 2

Brand: Equity Pages: 2

Brand: Equity Pages: 4

Brand: WAGNER Pages: 208

Brand: Black Widow Pages: 4

Brand: Code Alarm Pages: 13

Brand: Home Pages: 7

Brand: Paser Pages: 4

Brand: no-flame Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands