Xtrails VESDA-E VEP-A00 Product Manual Download

Page: 63 / 109

VESDA-E VEP-A00-P Product Guide

www.xtralis.com

5.5

Configuration Options

The VESDA-E VEP-A00 detector can be configured using the Xtralis VSC software.

The following sections describe the configuration options available in Xtralis VSC.

5.5.1

General Options

The General options include some basic identification information for the detector.

Figure 5-11: General Options

The General configuration options for the detector are as follows:

Network Name:

The name of the VESDAnet network. (The user can leave this blank if desired.).

Location:

A description of the physical location of the detector. This name will appear on Xtralis VSC

and on the LCD display of the A10 model detector.

Serial Number:

The serial number of the device. This is factory set and cannot be changed.

VESDA Zone:

The unique zone number used to link this detector and remote display/relay devices or

remote relay which output alarm and trouble status for this detector to the Fire Alarm Control Panel.

Authentication

Change Password:

The password used to authenticate Ethernet access. Refer to Section 5.3.1 on

page 51 for further information.

5.5.2

VESDAnet Options

The VESDAnet options provide the ability to control network data transmission behaviour for VESDAnet
connections.

Note:

Refer to Section 5.6 for the default settings.

Summary of Contents for VESDA-E VEP-A00














































































































Search results

Summary of Contents for VESDA-E VEP-A00

Reviews:

Related manuals for VESDA-E VEP-A00

Brands by name

Popular brands

Xtrails VESDA-E VEP-A00, Product Manual

Search results

Summary of Contents for VESDA-E VEP-A00

Reviews:

Related manuals for VESDA-E VEP-A00

Brands by name

Popular brands