background image

 

User Manual 

XProHeli Silk Gimbal

 

 

Silk Gimbal 

Page 42 

©2014 XPROHELI. All Rights Reserved.  

RC Settings in GUI 

 

i. ROLL, PITCH, YAW – Controls the position of the camera. 

ii. CMD – Allows you to execute specified actions. Configure 
your 2- or 3-position switch on your RC transmitter for a 
specified channel and assign it to the CMD channel. Its 
range is split into 3 sections : LOW, MID, HIGH. When 
changing the position of your RC transmitter switch, the 
signal jumps from one section to another, and the assigned 
command is executed.  

iii. FC_ROLL, FC_PITCH – Used to mark any PWM input to be a 
signal from the external flight controller. (This is an advanced 
feature that we do not recommend) 

RC MIX – You can mix 2 inputs together before applying 
them to the ROLL, PITCH or YAW axis. This feature enables 
you to control the camera from two sources, a joystick and 
RC transmitter, for example. You can adjust the proportion of 
the mix from 0 to 100%. 

ANGLE MODE – The RC transmitter will control the camera 
angle directly. The full RC range will move the camera from 
min to max angles, as specified above. If the RC transmitter 
stick does not move, the camera stands still. The speed of 
rotation depends on the “SPEED” and acceleration limiter 
settings. 

SPEED MODE – The RC transmitter will control the rotation 
speed. If the stick is centered, the camera stands still. If the 

Summary of Contents for Silk Gimbal


















































Reviews: