Xero88 CHILLI DIMMER Operating Manual Download

Page: 30 / 30

Technical Specification

Chilli Dimmer 73-853-00 Issue 8

Page 30 of 30

Technical Specification

Electrical

Supply Voltage:

230V +10% / -15%

Supply Frequency:

45 to 65Hz

Maximum Supply Current:

0410i:

40A Single phase

0410HF:

40A Single phase

1210i:

40A 3 phase star

1210HF:

40A 3 phase star

1216i:

64A 3 phase star

2410i:

80A 3 phase star

2416i:

128A 3 phase star

625i:

50A 3 phase star

Maximum Load per Channel

0410i:

10A Max

0410HF:

10A Max

1210i:

10A Max

1210HF:

10A Max

1216i:

16A Max

2410i:

10A Max

2416i:

16A Max

625i:

25A Max

DMX Input:

USITT DMX512/1990
Ground referenced receiver
Internal switchable termination

RDM Support:

Protocol Version:

1.0

Device Model ID:

The  first  5  digits  of  the  stock
number  are  used  for  this,  e.g.
01105  (0x0451)  for  the  Chilli
Pro 1210i.

Supported Parameters:

DMX_START_ADDRESS,
SENSOR_DEFINITION,
SENSOR_VALUE,
DEVICE_LABEL,
MANUFACTURER_LABEL,
DEVICE_MODEL_DESCRIPTION

Sub Devices:

One per channel.

Mechanical

Size:

0410i:

400 x 220 x 155 mm

0410HF:

400 x 220 x 155 mm

1210i:

850 x 325 x 155 mm

1210HF:

550 x 220 x 155 mm

1216i:

850 x 325 x 155 mm

2410i:

1000 x 632 x 155 mm

2416i:

1000 x 632 x 155 mm

625i:

850 x 325 x 155 mm

Maximum Weight:

0410i:

7.0 Kg

0410HF:

4.0 Kg

1210i:

18.0 Kg

1210HF:

9.0 Kg

1216i:

24.0 Kg

2410i:

47.0 Kg

2416i:

50.0 Kg

625i:

26.5 Kg

Environmental

Operating Temperature Range:

+5°C to +40°C

Relative Humidity:

5% to 95% Non-condensing

EMC

Emissions:

EN55015 : 2000
+A1 : 2001
+A2 : 2002

Immunity:

EN61000-6-1 : 2001
EN61000-6-3 : 2001

Electrical Safety:

EN60950-1 : 2002

Cooper Controls Ltd.
Usk House
Llantarnam Park
Cwmbran
Gwent NP44 3HD
United Kingdom

Tel: +44 (0)1633 838088 *
Fax: +44 (0)1633 867880
e-mail: [email protected]
Web:

www.zero88.com

* 24 hour answerphone

Summary of Contents for CHILLI DIMMER































Search results

Summary of Contents for CHILLI DIMMER

Reviews:

Related manuals for CHILLI DIMMER

Brands by name

Popular brands

Xero88 CHILLI DIMMER, Operating Manual

Search results

Summary of Contents for CHILLI DIMMER

Reviews:

Related manuals for CHILLI DIMMER

Brands by name

Popular brands