background image

975-0727-01-01

iii

Important Safety Instructions

IMPORTANT:

 R

EAD

 

AND

 

SAVE

 

THIS

 O

WNER

S

 G

UIDE

 

FOR

 

FUTURE

 

REFERENCE

.

This guide contains important safety instructions for the Freedom HFS Sine 
Wave Inverter/Charger that must be followed during operation and 
troubleshooting. 

Read and keep this Owner’s Guide for future 

reference.

Read these instructions carefully and look at the equipment to become 
familiar with the device before trying to install, operate, service or maintain 
it. The following special messages may appear throughout this bulletin or 
on the equipment to warn of potential hazards or to call attention to 
information that clarifies or simplifies a procedure.

The addition of either symbol to a “Danger” or “Warning” 
safety label indicates that an electrical hazard exists which 
will result in personal injury if the instructions are not 
followed.

This is the safety alert symbol. It is used to alert you to 
potential personal injury hazards. Obey all safety 
messages that follow this symbol to avoid possible injury 
or death.

DANGER

 indicates an imminently hazardous situation, which, if not 

avoided, will result in death or serious injury.

WARNING

 indicates a potentially hazardous situation, which, if not 

avoided, can result in death or serious injury.

CAUTION

 indicates a potentially hazardous situation, which, if not 

avoided, can result in moderate or minor injury.

NOTICE

 indicates a potentially hazardous situation, which, if not 

avoided, can result in equipment damage.

These notes describe things which are important for you 

to know, however, they are not as serious as a caution or warning.

IMPORTANT: 

Freedom HFS IC Owners Guide.book  Page iii  Friday, September 11, 2015  2:54 PM

Summary of Contents for 807-1055



























































Reviews: