Worthington CryoCe10K Instruction Manual Download

Page: 63 / 87

Instruction Manual

K SERIES Cryostorage System

IM: CryoCeK
Revision: 02
Approved by: CB
Page

10 MANUFACTURER'S DECLARATION

This Worthington Industries K SERIES Cryostorage System is manufactured by:

Worthington Cylinders GmbH

Beim Flaschenwerk 1
A-3291 Kienberg bei Gaming / Austria

Tel

+43 7485 606 0

Fax

+43 7485 606 100

E-Mail

[email protected]

As the manufacturer we declare under our sole responsibility that the

Worthington Industries K SERIES Cryostorage System

is a class IIa medical device

and complies with the EU Directive

93/42/EEC (Medical Device Directive).

This conformity is indicated by the CE mark followed by the registration number 0044 of the notified
body TÜV Nord Cert GmbH, Langemarckstraße 20, 45141 Essen, Germany.

This Worthington Industries K SERIES Cryostorage System complies with the following EU Directives

WEEE - Directive 2012/19/EU (Waste of Electrical and Electronic Equipment)

RoHS 2 - Directive 2011/65/EU (Restriction of Hazardous Substances in Electrical and Electronic
Equipment)

NOTE

A copy of the Declaration of Conformity is supplied with the K SERIES Cryostorage System

and is also available upon request.

Summary of Contents for CryoCe10K
























































































Search results

Summary of Contents for CryoCe10K

Reviews:

Related manuals for CryoCe10K

Brands by name

Popular brands

Worthington CryoCe10K, Instruction Manual

Search results

Summary of Contents for CryoCe10K

Reviews:

Related manuals for CryoCe10K

Brands by name

Popular brands