background image

Safety—General Precautions

DX,MSDS,NA -19-03MAR93-1/1

DX,DRAIN -19-01JUN15-1/1

TX,ASH,DISP -19-20JAN11-1/1

Handle Chemical Products Safely

Direct exposure to hazardous chemicals can cause
serious injury. Potentially hazardous chemicals used with
John Deere equipment include such items as lubricants,
coolants, paints, and adhesives.

A Material Safety Data Sheet (MSDS) provides specific
details on chemical products: physical and health hazards,
safety procedures, and emergency response techniques.

Check the MSDS before you start any job using a
hazardous chemical. That way you will know exactly what
the risks are and how to do the job safely. Then follow
procedures and recommended equipment.

(See your John Deere dealer for MSDS’s on chemical
products used with John Deere equipment.)

TS1

132

—UN—15APR13

Decommissioning — Proper Recycling and
Disposal of Fluids and Components

Safety and environmental stewardship measures must
be taken into account when decommissioning a machine
and/or component. These measures include the following:

Use appropriate tools and personal protective
equipment such as clothing, gloves, face shields or
glasses, during the removal or handling of objects and
materials.

Follow instructions for specialized components.

Release stored energy by lowering suspended machine
elements, relaxing springs, disconnecting the battery
or other electrical power, and releasing pressure in
hydraulic components, accumulators, and other similar
systems.

Minimize exposure to components which may have
residue from agricultural chemicals, such as fertilizers
and pesticides. Handle and dispose of these
components appropriately.

Carefully drain engines, fuel tanks, radiators, hydraulic
cylinders, reservoirs, and lines before recycling
components. Use leak-proof containers when draining
fluids. Do not use food or beverage containers.

Do not pour waste fluids onto the ground, down a drain,
or into any water source.

Observe all national, state, and local laws, regulations,
or ordinances governing the handling or disposal of
waste fluids (example: oil, fuel, coolant, brake fluid);

TS1

133

—UN—15APR13

filters; batteries; and, other substances or parts.
Burning of flammable fluids or components in other than
specially designed incinerators may be prohibited by law
and could result in exposure to harmful fumes or ashes.

Service and dispose of air conditioning systems
appropriately. Government regulations may require
a certified service center to recover and recycle air
conditioning refrigerants which could damage the
atmosphere if allowed to escape.

Evaluate recycling options for tires, metal, plastic,
glass, rubber, and electronic components which may be
recyclable, in part or completely.

Contact your local environmental or recycling center, or
your John Deere dealer for information on the proper
way to recycle or dispose of waste.

Exhaust Filter Ash Handling and Disposal

CAUTION: Under federal, state, and local laws or

regulations, exhaust filter ash can be classified
as a hazardous waste. Hazardous waste must
be disposed of in accordance with all applicable
federal, state, and local laws or regulations

governing hazardous waste disposal. Only a
qualified service provider should remove ash from
the exhaust filter. Personal protective equipment
and clothing, maintained in a sanitary and reliable
condition, should be used when handling and
cleaning exhaust filter. See your authorized dealer
for exhaust filter ash handling and disposal.

1-2-7

092221

PN=36

Summary of Contents for 380GLC

































































































































































































































































































Reviews: