Woodward DSLC, Installation And Operation Manual, Page: 30 / 114

DSLC Digital Synchronizer and Load Control Manual 02007
24 Woodward
Min. Max. Initial Dimen-
Name Value Value Value sion
Menu 3—Process Control
1. Process Control Gain 0.0001 100.0000 0.1000
2. Process Stability 0.00 20.00 1.00 seconds
3. Process Derivative 0.00 20.00 0.00 seconds
4. Process Deadband 0.00 20.00 0.10 mA
5. Process Droop 0.0 100.0 0.0 %
6. Process Filter 0.1 5.0 1.0 Hz
7. Process Reference 0.0 20.0 12.0 mA
8. Raise Reference Rate 0.01 20.00 0.10 mA/sec
9. Lower Reference Rate 0.01 20.00 0.10 mA/sec
10. High Limit PU 0.0 25.0 15.0 mA
11. High Limit DO 0.0 25.0 15.0 mA
12. High Limit Alarm Enabled/Disabled Disabled
13. Low Limit PU 0.0 25.0 10.0 mA
14. Low Limit DO 0.0 25.0 10.0 mA
15. Low Limit Alarm Enabled/Disabled Disabled
16. Process Switches Enabled/Disabled Disabled
Menu 4—VAR/Power Factor Control
1. VAR/PF Control Mode Disabled/ Disabled
PF Control/
VAR Control
2. VAR/PF Gain 0.01 22.00 1.00
3. VAR/PF Stability 0.00 20.00 2.50 seconds
4. Rated KVARs 0 30 000 (gen.) 100 kVAR
5. KVAR Reference 30 000 (abs.) 30 000 (gen.) 20 (gen.) kVAR
6. PF Reference 0.00 lagging 0.00 leading 0.8 lagging
7. PF Deadband 0.000 1.000 0.025
8. Voltage Reference 50.0 300xPT ratio 70xPT ratio V (L-L,L-N)
9. Voltage Trim Enabled/Disabled Disabled
10. Voltage Regulation 1.0 10.0 2.0 %
11. Voltage Low Limit 50 300xPT ratio 60xPT ratio V (L-L,L-N)
12. Voltage Low Alarm Enabled/Disabled Disabled
13. Voltage High Limit 50 300xPT ratio 80xPT ratio V (L-L,L-N)
14. Voltage High Alarm Enabled/Disabled Disabled
15. Voltage Switches Enabled/Disabled Enabled
16. Voltage Range Alarm Enabled/Disabled Disabled
17. Voltage Ramp Time 1 600 60 seconds
Menu 5—Configuration
1. Configuration Key 0 100 0
2. PT Winding Ratio 1:1 1000.0:1 1.0:1
3. CT Rating 5:5 10 000:5 5:5
4. PT Voltage Input 120/240 120
5. Voltage Display V (L-L), V (L-N) kV (L-L), kV (L-N) V (L-N)
6. System Frequency 50/60 60 Hz
7. Process Control Action Direct/Indirect Indirect
8. Network Address 1 16 0 (unconfigured)
9. Network Service Pin transmits unique ID code to network
Menu 6—Calibration
1. Calibration Key 0 100 0
2. Process Input 0 22 n/a mA
3. Remote Input 0 22 n/a mA
4. Speed Bias Output  100 +100 n/a %
5. Voltage Bias Output  100 +100 n/a %
6. PT Phase A 0 300 n/a volts
7. PT Phase B 0 300 n/a volts
8. PT Phase C 0 300 n/a volts
9. CT Phase A 0 7xCT rating n/a amperes
10. CT Phase B 0 7xCT rating n/a amperes
11. CT Phase C 0 7xCT rating n/a amperes
12. Bus Voltage 0 300 n/a volts
13. Synchroscope  57.3 +57.3 n/a degrees