background image

 

Display:

 

The red alarm LED in the smoke control panel and the red LED in the break glass unit are lit. 
The yellow malfunction LED in the break glass unit and the corresponding yellow malfunction LED in the 
smoke control panel flash. The green operating LED stops lighting. 

 

Option: Accumulative signalling of the alarm or malfunction signal (module WSA 301) 

It is possible to send an alarm or malfunction signal potential free, by plugging in the alarm/malfunction 
signalling module.  
The sending of the alarm can be stopped. If this is done, the yellow LED on the module will lit.  
 
Multi malfunction warning 
1 x change-over contact (max. load: 60V, 1A) with 3 pole connection terminal for potential free transmission 
to the BMS / panel etc. 
2 pole connection terminal for 2 wire BUS cable for the feedback of malfunctions in cascaded control units to 
the break glass unit connected to the master smoke control panel.  
 
Alarm message 
1 x change-over contact (max. load: 60V, 1A) with 3 pole connection terminal for potential free transmission 
to BMS / panel etc., or as monitored 2 wire alarm cable for cascading control panels. 
 
Jumper plugged in J1 = Only for the alarm transmission to the next smoke control panel (cascading). 
Jumper plugged in J2 = pot.-free alarm contact (factory setting). 
The transmitting can be interrupt. If so, it will be shown by the yellow LED. 
 

Option: Cascading smoke control panels (module WSA 301)

 

The smoke control panels can be cascaded by a monitored 2 wire connection from the alarm module of the 
master smoke control panel to the smoke detector input of the slave central panel. 
A malfunction in the cascaded smoke control panels is detected via the 2 wire BUS cable. The malfunction is 
only displayed in the corresponding smoke control panel and in the break glass unit connected to the master 
smoke control panel (primary break glass unit type WSK 320). 
 

Option: ASV connection (module WSA 306)

 

The smoke detector input can be used for receiving a signal from an external fire detecting system (ASV). This 
requires a potential-free ASV contact and the ASV module WSA 306. 

 

WSC 204 / WSC 204KP / WSC 204MH: ABA OPEN 
To generate a trip (EMERGENCY OPEN) of the smoke ventilation group actuate the potential-free contact in 
the ASV. All smoke ventilation actuators “OPEN” automatically. An acoustic signal will sounds in the primary 
break glass unit (if mounted). The ventilation function/buttons are now out of operation. 

 

WSC 204BZ: ABA CLOSE 
To generate a trip (EMERGENCY CLOSE) of the smoke ventilation group actuate the potential-free contact in 
the ASV. All smoke ventilation actuators “CLOSE” automatically. An acoustic signal will sounds in the primary 
break glass unit (if mounted). The ventilation function/buttons are now out of operation. 

 

The break glass unit has higher priority than ASV. 
 

4.2.  Ventilation functions 

Ventilation OPEN 

If the momentary function is activated (SW2/2 = ON), the actuators only move open for as long as the OPEN 
button of the ventilation button is kept pressed. (CLOSE still has self hold.) 
If the latching function is activated (SW2/2 = OFF), the actuators open after pressing the OPEN button. 

Display:

 The ventilation open LED in the ventilation button is lit (only with LED integrated in the button). 

 

Ventilation stop 

The actuators stop when both buttons are pressed. 

Display:

 The ventilation open LED in the ventilation button remains lit (only with LED integrated in the button). 

 

Ventilation closed 

The actuators close after pressing the CLOSED button. 

Display: 

The ventilation open LED in the ventilation button has extinguished (only with LED integrated in the 

button). 
 

Summary of Contents for WSC 204





















Reviews: