background image

s

e C t I o n

 4� 2—u

s I n G

 

t h e

 W

I l s o n

 l

I f t

 

t o

 I

n s ta l l

 s

P I k e s

  

43

W i l s o n   A u d i o   S p e c i a l t i e s

42

  Chronosonic 

XVX

 Inst allation Guide

A u t h e n t i c   E x c e l l e n c e

Section 4.1—Spike Installation

Spike Assembly

• 

Remove the mechanical diodes and move the nut to about two 
threads from the point. This will allow for  greater movement 
when leveling the loudspeaker system. 

• 

Screw the spikes into the diode until the nut is against the 
diode. Be careful that the nut does not turn while inserting and 
threading spikes into the diode. 

Note: Do not tighten these assembled spikes. You will need to unscrew 
them when you level the Chronosonic XVX. 

• 

Place the set screw into the other end of the diode with the Al-
len head toward the spike. This will ensure that if for any reason 
you have to remove your Chronosonic XVX spikes, you will be 
able to withdraw the set screw safely using the supplied Allen 
wrench. Screw the set screw into the diode until it meets the 
spike. 

• 

Place the assemblies out of the traffic pattern until they are 
needed during the installation.

Section 4.2—Using the Wilson Lift to Install Spikes

Note: This is a two person job. Do not attempt this by yourself. The Chrono-

sonic XVX weighs over 685 LBS and may seriously injure someone if tipped 
over.

Materials Required

• 

8 sets of assembled spikes

• 

The Wilson Audio Lift

• 

The lift socket wrench 

• 

Swivel caster wrench

Installation Procedure

1.  Slide the Wilson Audio Lift under the front of the Chronosonic 

XVX, centered between the casters, so that the jack’s lift bolt 
is exposed. Place the lift plate so it is positioned about an inch 
behind the front facade of the Chronosonic XVX woofer enclo-
sure. 

Note: An assistant should stand to the rear of the Chronosonic XVX to 
steady it.

2.  Attach the wrench to the lift bolt and begin to slowly raise the 

front of the Chronosonic XVX by turning the bolt clockwise.

3.  After the front of the Chronosonic XVX is high enough (you will 

need approximately one and a half inches of clearance beneath 

Summary of Contents for Chronosonic XVX





































Reviews: