s
e C t I o n
2 �4 —C
o n f I G u r I n G
t h e
u
P P e r
s
u b M o d u l e
23
W i l s o n A u d i o S p e c i a l t i e s
22
Chronosonic
XVX
Inst allation Guide
Note: This part of the install process must be completed before you install
the modules into the Gantry.
1. Refer to the chart in Section 6 called “XVX Lower Midrange
Module Spike Length.” Using the measured ear height and
speaker distance, refer to the intersecting box in the chart. If
there is a number in the converging box, the Chronosonic XVX
Lower Midrange Module requires a spike. The spike number is
stamped into the flat surface at the top of the spike. From the
toolkit, locate the required spike, and install it into the rear
spike receptacle on the bottom of the module.
2. At the same time, install the two ball-end spikes into the front
receptacles of the Lower Midrange Module.
3. The 4-Inch module installs into the captive, winged receptacle
on the upper portion of the Lower Midrange Module. Install
the “A” spikes into its front receptacles. An oval-topped tension
spike is pre-installed into the rear shelf of the 4-inch module.
4. Refer to the table In Section 6 labeled “XVX Lower 4-inch Mid
Detent Position.” This table indicates the detent location in
which the right front spike rests.
5. Raise the tension spike located at the rear of the 4-inch Mid-
range Module such that the spike is not protruding through
the bottom surface. This will enable the module to freely move
A u t h e n t i c E x c e l l e n c e
™
into the Lower Midrange Module without risk of scratching the
painted surfaces.
6. Install the 4-inch Module into the winged receptacle in the
Lower Midrange Module.
7. The right spike track on the top surface of the Lower Midrange
Module contains calibrated numbers for this process. It is nec-
essary to adjust the 4-inch Module fore-to-aft in such that right
“A” spike rests on the correct number as indicated by the chart.
Locate the correct number and carefully slide the 4-inch Mod-
ule such that the spike is positioned above the correct detent.
Carefully tighten the rear tension spike, making sure that the
front-right spike remains centered on the proper detent.
8. The lower submodule is installed into the Chronosonic XVX
Gantry Array in this assembled form. Return the assembled
submodule to the staged area.
Section 2.4—Configuring the Upper Submodule
1. Rest the Tweeter on a safe surface.
2. Install two “A” spikes into the top front receptacles of the
Tweeter Module. Install a ball post into the top rear of the
module.
Summary of Contents for Chronosonic XVX
