WIKA CPT-2 series Operating Instructions Manual Download Page 17

Page: 17 / 84

4 Mounting

WIKA Operating Instructions - Process pressure transmitter CPT-2x

Fig. 11: Position of the filter element

1 Plastic, stainless steel single chamber (precision casting)

2 Aluminium - single chamber

3 Stainless steel single chamber (electropolished)

4 Plastic double chamber

5 Aluminium - double chamber

6 Filter element

With the following instruments a blind plug is installed instead of the

filter element:

•

Instruments in protection IP66/IP68 (1 bar) - ventilation via capillar-

ies in non-detachable cable

•

Instruments with absolute pressure

→

Turn the metal ring in such a way that the filter element points

downward after installation of the instrument. This provides better

protection against buildup.

Fig. 12: Position of the filter element - Ex-d version

1 Rotatable metal ring

2 Filter element

Instruments with absolute pressure have a blind plug mounted

instead of the filter element.

Filter element - Position

Ex-d version

Summary of Contents for CPT-2 series





















































































Search results

Summary of Contents for CPT-2 series

Reviews:

Related manuals for CPT-2 series

Brands by name

Popular brands

WIKA CPT-2 series, Operating Instructions Manual

Search results

Summary of Contents for CPT-2 series

Reviews:

Related manuals for CPT-2 series

Brands by name

Popular brands