WIKA CPT-2 series Operating Instructions Manual Download Page 10

Page: 10 / 84

3 Product description

WIKA Operating Instructions - Process pressure transmitter CPT-2x

The measuring cell design depends on the selected pressure type.

Relative pressure

: the measuring cell is open to the atmosphere.

The ambient pressure is detected in the measuring cell and compen-

sated. It thus has no influence on the measured value.
Absolute pressure

: the measuring cell contains vacuum and is

encapsulated. The ambient pressure is not compensated and does

hence influence the measured value.

The following presentations show examples for the installation of the

ceramic measuring cell into the process fitting and the different seal

concepts.

The recessed installation is particularly suitable for applications with

gases, vapours and clear liquids. The measuring cell seal is posi-

tioned laterally as well as in addition in front.

3
4

Fig. 4: Recessed installation of the measuring cell (example: manometer con-

nection G½)
1 Measuring cell

2 Seal for the measuring cell

3 Additional, front seal for measuring cell

4 Diaphragm

5 Process fitting

6 Seal for the process fitting

The front-flush installation is particularly suitable for applications with

viscous and abrasive media and in case of buildup. The measuring

cell seal is positioned laterally.

Pressure types

Seal concepts

Recessed installation

Front-flush mounting with

single seal

Summary of Contents for CPT-2 series





















































































Search results

Summary of Contents for CPT-2 series

Reviews:

Related manuals for CPT-2 series

Brands by name

Popular brands

WIKA CPT-2 series, Operating Instructions Manual

Search results

Summary of Contents for CPT-2 series

Reviews:

Related manuals for CPT-2 series

Brands by name

Popular brands